Evaluation of hardwaresupport for the Framework 16 notebook

[jjkarcher]

@jws

Thank you for the devices report that looks normal. I assume you also use a 7040 series based system and you use the regular base-nova Sculpt OS variant.

You are correct on both of those assumptions. (Internal GPU.) Sorry I didn’t specify those in advance. (I should try the base-hw variant also; I didn’t think of that.)

@jws

I’ve prepared an image (sig) that contains some diagnostic messages (invalid caps in the platform driver are logged) and also some messages in the nvme driver that may help to pin-point the shortcoming.

Thanks for doing that! I will try that shortly.

@jws

(As a disclaimer: I appreciate that you are testing Sculpt OS on AMD but please note that such systems are still not officially supported and I especially would not recommend using a mobile AMD system for Sculpt for the moment.)

Don’t worry, expectations are set correctly.

I would just like to say again - thank you to the entire Genode team for putting so much effort into the (non-commercial) community! It’s a rare treat in this world!

[jws]

@jjkarcher, @Nos I’ve publish another image (sig) that in addition to the NVMe debug commits contains the usb_net driver configured in a way that it should work with 8156 dongles used with the Framework.

Since it still needs some manual attention, here is a step-by-step guide. After booting the image from USB

❶ Select either Wired or Wifi in the network dialog (we just want the sculpt_manager to generate a configuration file at this point)
❷ Inspect any file-system
❸ cp /config/managed/nic_router /config
❹ vim /config/nic_router and replace 'wifi → ’ or 'nic → in the policy node with 'usb_net → ’

At this point you should get an IP address via the Realtek USB network dongle. Other devices might also work but require editing /config/usb (look for the usb_net policy).

[jjkarcher]

Wow, thanks! I’ll try that right away.

I did try it with the standard base-hw, and got the same results. Then I tried it with your special 2026-01-22 build, and here is the log from that:

0.0 [kernel] [ 0] TSC:3792970 kHz BUS:24000 kHz (measured)
0.0 [kernel] [ 0] CORE:00:00:0 19:74:1:0 [0] AMD Ryzen 7 7840HS w/ Radeon 780M Graphics      MWAIT+E+I XS
0.0 [kernel] [ 1] CORE:00:00:1 19:74:1:0 [0] AMD Ryzen 7 7840HS w/ Radeon 780M Graphics      MWAIT+E+I XS
0.0 [kernel] [ 7] CORE:00:03:1 19:74:1:0 [0] AMD Ryzen 7 7840HS w/ Radeon 780M Graphics      MWAIT+E+I XS
0.0 [kernel] [ 6] CORE:00:03:0 19:74:1:0 [0] AMD Ryzen 7 7840HS w/ Radeon 780M Graphics      MWAIT+E+I XS
0.0 [kernel] [ 8] CORE:00:04:0 19:74:1:0 [0] AMD Ryzen 7 7840HS w/ Radeon 780M Graphics      MWAIT+E+I XS
0.0 [kernel] [14] CORE:00:07:0 19:74:1:0 [0] AMD Ryzen 7 7840HS w/ Radeon 780M Graphics      MWAIT+E+I XS
0.0 [kernel] [13] CORE:00:06:1 19:74:1:0 [0] AMD Ryzen 7 7840HS w/ Radeon 780M Graphics      MWAIT+E+I XS
0.0 [kernel] [ 3] CORE:00:01:1 19:74:1:0 [0] AMD Ryzen 7 7840HS w/ Radeon 780M Graphics      MWAIT+E+I XS
0.0 [kernel] [12] CORE:00:06:0 19:74:1:0 [0] AMD Ryzen 7 7840HS w/ Radeon 780M Graphics      MWAIT+E+I XS
0.0 [kernel] [ 9] CORE:00:04:1 19:74:1:0 [0] AMD Ryzen 7 7840HS w/ Radeon 780M Graphics      MWAIT+E+I XS
0.0 [kernel] [ 2] CORE:00:01:0 19:74:1:0 [0] AMD Ryzen 7 7840HS w/ Radeon 780M Graphics      MWAIT+E+I XS
0.0 [kernel] [ 4] CORE:00:02:0 19:74:1:0 [0] AMD Ryzen 7 7840HS w/ Radeon 780M Graphics      MWAIT+E+I XS
0.0 [kernel] [ 5] CORE:00:02:1 19:74:1:0 [0] AMD Ryzen 7 7840HS w/ Radeon 780M Graphics      MWAIT+E+I XS
0.0 [kernel] [11] CORE:00:05:1 19:74:1:0 [0] AMD Ryzen 7 7840HS w/ Radeon 780M Graphics      MWAIT+E+I XS
0.0 [kernel] [10] CORE:00:05:0 19:74:1:0 [0] AMD Ryzen 7 7840HS w/ Radeon 780M Graphics      MWAIT+E+I XS
0.0 [kernel] [15] CORE:00:07:1 19:74:1:0 [0] AMD Ryzen 7 7840HS w/ Radeon 780M Graphics      MWAIT+E+I XS
0.0 [core] Hypervisor features IOMMUe[0m
0.0 [core] Hypervisor features SVMe[0m
0.0 [core] Hypervisor reports 8x2 CPUse[0m
0.0 [core] mapping: affinity space -> kernel cpu id - package:core:threade[0m
0.0 [core]  remap (0x0) -> 0 - 0:0:0 boot cpue[0m
0.0 [core]  remap (0x1) -> 1 - 0:0:1e[0m
0.0 [core]  remap (1x0) -> 2 - 0:1:0e[0m
0.0 [core]  remap (1x1) -> 3 - 0:1:1e[0m
0.0 [core]  remap (2x0) -> 4 - 0:2:0e[0m
0.0 [core]  remap (2x1) -> 5 - 0:2:1e[0m
0.0 [core]  remap (3x0) -> 6 - 0:3:0e[0m
0.0 [core]  remap (3x1) -> 7 - 0:3:1e[0m
0.0 [core]  remap (4x0) -> 8 - 0:4:0e[0m
0.0 [core]  remap (4x1) -> 9 - 0:4:1e[0m
0.0 [core]  remap (5x0) -> 10 - 0:5:0e[0m
0.0 [core]  remap (5x1) -> 11 - 0:5:1e[0m
0.0 [core]  remap (6x0) -> 12 - 0:6:0e[0m
0.0 [core]  remap (6x1) -> 13 - 0:6:1e[0m
0.0 [core]  remap (7x0) -> 14 - 0:7:0e[0m
0.0 [core]  remap (7x1) -> 15 - 0:7:1e[0m
0.0 [core] ROM modules:
0.0 [core]  ROM: [00000000573cf000,00000000573d0742) LICENSE.bitstream-vera
0.0 [core]  ROM: [00000000545c9000,00000000545c9006) VERSION
0.0 [core]  ROM: [00000000549fe000,0000000054a0e18c) Vera.ttf
0.0 [core]  ROM: [0000000052c8c000,0000000052c98048) VeraMono.ttf
0.0 [core]  ROM: [00000000533ea000,0000000053418778) acpi
0.0 [core]  ROM: [00000000549c0000,00000000549fd040) ahci
0.0 [core]  ROM: [0000000053660000,0000000053683130) backdrop
0.0 [core]  ROM: [0000000057438000,0000000057593800) bash-minimal.tar
0.0 [core]  ROM: [0000000054baa000,0000000054bbfe78) boot_fb
0.0 [core]  ROM: [00000000545ca000,00000000545ca0b3) build_info
0.0 [core]  ROM: [0000000057594000,00000000575bd9a0) cached_fs_rom
0.0 [core]  ROM: [0000000054d2b000,0000000054d52e70) chroot
0.0 [core]  ROM: [0000000054dbd000,0000000054de4180) clipboard
0.0 [core]  ROM: [0000000053029000,000000005302d8bd) config
0.0 [core]  ROM: [0000000000074000,0000000000078000) core_log
0.0 [core]  ROM: [00000000545cb000,0000000054726800) coreutils-minimal.tar
0.0 [core]  ROM: [0000000053686000,000000005373dcb0) curl.lib.so
0.0 [core]  ROM: [0000000053b25000,0000000053b27800) depot.tar
0.0 [core]  ROM: [0000000052d59000,0000000052d89948) depot_deploy
0.0 [core]  ROM: [0000000053684000,0000000053685030) depot_download.config
0.0 [core]  ROM: [0000000053fbc000,000000005400ee18) depot_download_manager
0.0 [core]  ROM: [0000000052c99000,0000000052cdc300) depot_query
0.0 [core]  ROM: [0000000054d68000,0000000054db7f78) dialog.lib.so
0.0 [core]  ROM: [0000000057cd3000,0000000057cd35d6) drop_shadow.png
0.0 [core]  ROM: [0000000052f45000,0000000052fea770) e2fsck
0.0 [core]  ROM: [0000000053f08000,0000000053f50b38) event_filter
0.0 [core]  ROM: [0000000053b28000,0000000053b370a0) extract
0.0 [core]  ROM: [0000000056bc4000,0000000056bd8f88) fetchurl
0.0 [core]  ROM: [0000000054899000,00000000548bad58) file_terminal
0.0 [core]  ROM: [00000000531e5000,000000005320b800) fs_query
0.0 [core]  ROM: [0000000057415000,0000000057437d68) fs_report
0.0 [core]  ROM: [0000000057357000,000000005737b0b8) fs_rom
0.0 [core]  ROM: [0000000056bd9000,0000000056bf8ec8) fs_tool
0.0 [core]  ROM: [0000000054db8000,0000000054dbcd38) genode_logo.png
0.0 [core]  ROM: [0000000056dab000,0000000056dd43d8) global_keys_handler
0.0 [core]  ROM: [0000000054b6b000,0000000054b8df48) gpt_write
0.0 [core]  ROM: [0000000054c84000,0000000054caa588) gui_fader
0.0 [core]  ROM: [0000000053f92000,0000000053fbb170) gui_fb
0.0 [core]  ROM: [0000000054b2f000,0000000054b52620) hpet_timer
0.0 [core]  ROM: [00000000545bf000,00000000545c9000) hrd.tar
0.0 [core]  ROM: [00000000544ef000,000000005456bce8) init
0.0 [core]  ROM: [0000000057f6f000,0000000057f70fbb) init.xsd
0.0 [core]  ROM: [000000005737c000,00000000573ce800) initial_config.tar
0.0 [core]  ROM: [00000000548bb000,000000005491f598) intel_gpu
0.0 [core]  ROM: [000000000009e000,000000000009f000) kernel_log
0.0 [core]  ROM: [0000000053dfb000,0000000053f07e00) ld.lib.so
0.0 [core]  ROM: [0000000057d67000,0000000057e27dc8) libarchive.lib.so
0.0 [core]  ROM: [000000005716b000,0000000057356d28) libc.lib.so
0.0 [core]  ROM: [000000005373e000,0000000053a89238) libcrypto.lib.so
0.0 [core]  ROM: [0000000052d2a000,0000000052d58970) liblzma.lib.so
0.0 [core]  ROM: [000000005302e000,00000000530752b8) libm.lib.so
0.0 [core]  ROM: [0000000053f51000,0000000053f91018) libpng.lib.so
0.0 [core]  ROM: [0000000053a8a000,0000000053b24bf8) libssh.lib.so
0.0 [core]  ROM: [000000005353a000,00000000535ee9e8) libssl.lib.so
0.0 [core]  ROM: [00000000535ef000,00000000535fe578) log_core
0.0 [core]  ROM: [0000000052d8a000,0000000052f448b0) lxip.lib.so
0.0 [core]  ROM: [0000000053dab000,0000000053dfad78) menu_view
0.0 [core]  ROM: [0000000054b8e000,0000000054ba9800) menu_view_styles.tar
0.0 [core]  ROM: [0000000056b40000,0000000056bb6030) mke2fs
0.0 [core]  ROM: [000000005320c000,000000005328c900) monitor
0.0 [core]  ROM: [0000000057d0f000,0000000057d66128) ncurses.lib.so
0.0 [core]  ROM: [0000000053150000,00000000531e4b98) nic_router
0.0 [core]  ROM: [0000000054d1d000,0000000054d1ee76) nic_router.xsd
0.0 [core]  ROM: [0000000053076000,00000000530f7670) nitpicker
0.0 [core]  ROM: [0000000054cdb000,0000000054d1c1c0) nvme
0.0 [core]  ROM: [0000000053d7c000,0000000053daaef0) part_block
0.0 [core]  ROM: [0000000056e1c000,000000005716a228) pc_intel_fb
0.0 [core]  ROM: [0000000056bf9000,0000000056d97228) pc_nic
0.0 [core]  ROM: [0000000054bc0000,0000000054c6c1e0) pc_platform
0.0 [core]  ROM: [0000000054727000,0000000054898e10) pc_usb_host
0.0 [core]  ROM: [00000000578c6000,0000000057cd2678) pc_wifi.lib.so
0.0 [core]  ROM: [0000000054ecf000,0000000056afe000) pc_wifi_firmware.tar
0.0 [core]  ROM: [0000000056b18000,0000000056b3f6d8) pci_decode
0.0 [core]  ROM: [0000000056bb7000,0000000056bc3800) plain_decorator_theme.tar
0.0 [core]  ROM: [0000000054e1c000,0000000054eaa258) platform
0.0 [core]  ROM: [0000000000070000,0000000000073000) platform_info
0.0 [core]  ROM: [00000000530f8000,000000005312ada8) pointer
0.0 [core]  ROM: [0000000054d1f000,0000000054d27560) posix.lib.so
0.0 [core]  ROM: [0000000054036000,000000005405c700) ps2
0.0 [core]  ROM: [0000000054eab000,0000000054eceb10) report_rom
0.0 [core]  ROM: [000000005328d000,00000000532dbdb0) resize2fs
0.0 [core]  ROM: [000000005312b000,000000005314fe50) rom_filter
0.0 [core]  ROM: [0000000054d53000,0000000054d674c0) rom_reporter
0.0 [core]  ROM: [0000000057e28000,0000000057f6ee20) rump.lib.so
0.0 [core]  ROM: [00000000543a3000,00000000544b2c28) rump_fs.lib.so
0.0 [core]  ROM: [000000005781a000,00000000578c5750) sandbox.lib.so
0.0 [core]  ROM: [000000005405d000,00000000543a24e8) sculpt_manager
0.0 [core]  ROM: [0000000054025000,0000000054035a78) shim
0.0 [core]  ROM: [0000000054d28000,0000000054d2a6f8) stdin2out
0.0 [core]  ROM: [0000000053b38000,0000000053d7c000) tclsh.tar
0.0 [core]  ROM: [0000000052cdd000,0000000052d29e50) terminal
0.0 [core]  ROM: [0000000053419000,00000000534190e2) terminal.config
0.0 [core]  ROM: [0000000054c6d000,0000000054c837f8) terminal_crosslink
0.0 [core]  ROM: [0000000054b53000,0000000054b6aa70) terminal_log
0.0 [core]  ROM: [0000000057cd4000,0000000057d0e8d0) text_area
0.0 [core]  ROM: [00000000573d1000,0000000057414700) themed_decorator
0.0 [core]  ROM: [0000000056afe000,0000000056b17e48) timer
0.0 [core]  ROM: [0000000052feb000,00000000530288d0) usb_block
0.0 [core]  ROM: [00000000532dc000,00000000533e9720) usb_hid
0.0 [core]  ROM: [0000000054920000,00000000549bf7c0) verify
0.0 [core]  ROM: [000000005456c000,00000000545bedc0) vesa_fb
0.0 [core]  ROM: [00000000544b3000,00000000544eee88) vfs
0.0 [core]  ROM: [000000005341a000,00000000534de6e8) vfs.lib.so
0.0 [core]  ROM: [0000000054dfe000,0000000054e1b3f8) vfs_import.lib.so
0.0 [core]  ROM: [0000000056d98000,0000000056daa750) vfs_jitterentropy.lib.so
0.0 [core]  ROM: [0000000054cab000,0000000054cda120) vfs_lxip.lib.so
0.0 [core]  ROM: [00000000575be000,00000000575d2750) vfs_pipe.lib.so
0.0 [core]  ROM: [0000000057f71000,0000000057f7d9c0) vfs_ram_log.lib.so
0.0 [core]  ROM: [000000005400f000,0000000054024658) vfs_rump.lib.so
0.0 [core]  ROM: [0000000056dd5000,0000000056e1bd50) vfs_ttf.lib.so
0.0 [core]  ROM: [00000000575d3000,0000000057819800) vim-minimal.tar
0.0 [core]  ROM: [0000000054b07000,0000000054b2efa8) wifi
0.0 [core]  ROM: [00000000535ff000,000000005365f6f8) wm
0.0 [core]  ROM: [00000000534df000,0000000053539c28) wpa_driver_nl80211.lib.so
0.0 [core]  ROM: [0000000054a0f000,0000000054b06558) wpa_supplicant.lib.so
0.0 [core]  ROM: [0000000054de5000,0000000054dfd230) zlib.lib.so
e[0m0.0 [core] 591900K kernel memorye[0m
e[0m0.0 [core] Genode sculpt-25.10.1-5-g7c17643ba0 <local changes>e[0m
0.0 [core] 56485 MiB RAM and 63256 caps assigned to inite[0m
0.0 [runtime] parent providese[0m
0.0 [runtime]   service "ROM"e[0m
0.0 [runtime]   service "PD"e[0m
0.0 [runtime]   service "RM"e[0m
0.0 [runtime]   service "CPU"e[0m
0.0 [runtime]   service "LOG"e[0m
0.0 [runtime]   service "IO_MEM"e[0m
0.0 [runtime]   service "IO_PORT"e[0m
0.0 [runtime]   service "IRQ"e[0m
0.0 [runtime]   service "Gui"e[0m
0.0 [runtime]   service "Timer"e[0m
0.0 [runtime]   service "Block"e[0m
0.0 [runtime]   service "Report"e[0m
0.0 [runtime]   service "Platform"e[0m
0.0 [runtime] monitor readye[0m
0.0 [drivers -> acpi] Found HPET hw_id=0x10  vendor_id=0x1022 space_id=0x0 addr=0xfed00000 hpet_id=0x0e[0m
0.0 [drivers -> acpi] Found MADTe[0m
0.0 [drivers -> acpi] MADT IRQ 0 -> GSI 2 flags: 0e[0m
0.0 [drivers -> acpi] MADT IRQ 9 -> GSI 9 flags: 15e[0m
0.0 [drivers -> acpi] Found MCFGe[0m
0.0 [drivers -> acpi] MCFG BASE 0xe0000000 seg 0x0 bus 0x0-0xffe[0m
0.0 [drivers -> acpi] Found IVRSe[0m
0.0 [drivers -> acpi] XSDT OEM 'INSYDE', table id 'EDK2    ', revision 2, creator '    ' (16777235)e[0m
0.0 [drivers -> acpi] SMBIOSv2 table (entry point: 0x25000 structures: 0x58e75000)e[0m
0.1 [drivers -> pci_decode] e[34mWarning: Unsupported TPM2 device founde[0m
0.3 [runtime] parent providese[0m
0.3 [runtime]   service "VM"e[0m
0.3 [runtime]   service "Usb"e[0m
0.3 [runtime]   service "File_system"e[0m
0.3 [runtime]   service "Rtc"e[0m
0.3 [runtime]   service "TRACE"e[0m
0.3 [runtime]   service "Event"e[0m
0.3 [runtime]   service "Capture"e[0m
0.3 [runtime]   service "Gpu"e[0m
0.3 [runtime]   service "Pin_state"e[0m
0.3 [runtime]   service "Pin_control"e[0m
0.3 [runtime]   service "I2c"e[0m
0.3 [runtime]   service "Terminal"e[0m
0.3 [runtime] child "ps2"e[0m
0.3 [runtime]   RAM quota:  776Ke[0m
0.3 [runtime]   cap quota:  66e[0m
0.3 [runtime]   ELF binary: ps2e[0m
0.3 [runtime]   priority:   2e[0m
0.3 [runtime] child "boot_fb"e[0m
0.3 [runtime]   RAM quota:  16776Ke[0m
0.3 [runtime]   cap quota:  66e[0m
0.3 [runtime]   ELF binary: boot_fbe[0m
0.3 [runtime]   priority:   2e[0m
0.3 [runtime] child "usb"e[0m
0.3 [runtime]   RAM quota:  16136Ke[0m
0.3 [runtime]   cap quota:  166e[0m
0.3 [runtime]   ELF binary: usbe[0m
0.3 [runtime]   priority:   2e[0m
0.3 [runtime]   provides service Usbe[0m
0.3 [runtime] child "nvme"e[0m
0.3 [runtime]   RAM quota:  7944Ke[0m
0.3 [runtime]   cap quota:  66e[0m
0.3 [runtime]   ELF binary: nvmee[0m
0.3 [runtime]   priority:   3e[0m
0.3 [runtime]   provides service Blocke[0m
0.3 [runtime] child "runtime_view"e[0m
0.3 [runtime]   RAM quota:  53000Ke[0m
0.3 [runtime]   cap quota:  296e[0m
0.3 [runtime]   ELF binary: menu_viewe[0m
0.3 [runtime]   priority:   2e[0m
0.3 [runtime] child "ram_fs"e[0m
0.3 [runtime]   RAM quota:  776Ke[0m
0.3 [runtime]   cap quota:  266e[0m
0.3 [runtime]   ELF binary: vfse[0m
0.3 [runtime]   priority:   2e[0m
0.3 [runtime]   provides service File_systeme[0m
0.3 [runtime] child "ram_fs" announces service "File_system"e[0m
0.3 [runtime -> ps2] i8042: no controller detectede[0m
0.3 [runtime -> boot_fb] using boot framebuffer: 2560x1600x32 @ 0x8800000000 type=1 pitch=10240 -> 2560x1600e[0m
0.3 [runtime -> nvme] e[31mError: DBGDI:2498e[0m
0.6 [runtime] child "usb" announces service "Usb"e[0m
0.6 [runtime -> usb] SLUB: HWalign=64, Order=0-1, MinObjects=0, CPUs=1, Nodes=1e[0m
0.6 [runtime -> usb] NR_IRQS: 4352, nr_irqs: 4352, preallocated irqs: 256e[0m
0.6 [runtime -> usb] clocksource: dde_counter: mask: 0xffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 3526361616960 nse[0m
0.6 [runtime -> usb] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 nse[0m
0.6 [runtime -> usb] usbcore: registered new interface driver usbfse[0m
0.6 [runtime -> usb] usbcore: registered new interface driver hube[0m
0.6 [runtime -> usb] usbcore: registered new device driver usbe[0m
0.6 [runtime -> usb] clocksource: Switched to clocksource dde_countere[0m
0.6 [runtime -> usb] usbcore: registered new interface driver genodee[0m
0.6 [runtime -> usb] xhci_hcd c3:00.4: xHCI Host Controllere[0m
0.6 [runtime -> usb] xhci_hcd c3:00.4: new USB bus registered, assigned bus number 1e[0m
0.6 [runtime -> usb] xhci_hcd c3:00.4: hcc params 0x0110ffc5 hci version 0x120 quirks 0x0000000200000010e[0m
0.6 [runtime -> usb] xhci_hcd c3:00.4: xHCI Host Controllere[0m
0.6 [runtime -> usb] xhci_hcd c3:00.4: new USB bus registered, assigned bus number 2e[0m
0.6 [runtime -> usb] xhci_hcd c3:00.4: Host supports USB 3.1 Enhanced SuperSpeede[0m
0.6 [runtime -> usb] hub 1-0:1.0: USB hub founde[0m
0.6 [runtime -> usb] hub 1-0:1.0: 1 port detectede[0m
0.6 [runtime -> usb] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.e[0m
0.6 [runtime -> usb] hub 2-0:1.0: USB hub founde[0m
0.6 [runtime -> usb] hub 2-0:1.0: 1 port detectede[0m
0.6 [runtime -> usb] xhci_hcd c3:00.3: xHCI Host Controllere[0m
0.6 [runtime -> usb] xhci_hcd c3:00.3: new USB bus registered, assigned bus number 3e[0m
0.6 [runtime -> usb] xhci_hcd c3:00.3: hcc params 0x0110ffc5 hci version 0x120 quirks 0x0000000200000010e[0m
0.6 [runtime -> usb] xhci_hcd c3:00.3: xHCI Host Controllere[0m
0.6 [runtime -> usb] xhci_hcd c3:00.3: new USB bus registered, assigned bus number 4e[0m
0.6 [runtime -> usb] xhci_hcd c3:00.3: Host supports USB 3.1 Enhanced SuperSpeede[0m
0.6 [runtime -> usb] hub 3-0:1.0: USB hub founde[0m
0.6 [runtime -> usb] hub 3-0:1.0: 1 port detectede[0m
0.6 [runtime -> usb] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.e[0m
0.6 [runtime -> usb] hub 4-0:1.0: USB hub founde[0m
0.6 [runtime -> usb] hub 4-0:1.0: 1 port detectede[0m
0.6 [runtime -> usb] xhci_hcd c1:00.4: xHCI Host Controllere[0m
0.6 [runtime -> usb] xhci_hcd c1:00.4: new USB bus registered, assigned bus number 5e[0m
0.6 [runtime -> usb] xhci_hcd c1:00.4: hcc params 0x0110ffc5 hci version 0x120 quirks 0x0000000200000010e[0m
0.6 [runtime -> usb] xhci_hcd c1:00.4: xHCI Host Controllere[0m
0.6 [runtime -> usb] xhci_hcd c1:00.4: new USB bus registered, assigned bus number 6e[0m
0.6 [runtime -> usb] xhci_hcd c1:00.4: Host supports USB 3.1 Enhanced SuperSpeede[0m
0.6 [runtime -> usb] hub 5-0:1.0: USB hub founde[0m
0.6 [runtime -> usb] hub 5-0:1.0: 1 port detectede[0m
0.6 [runtime -> usb] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.e[0m
0.6 [runtime -> usb] hub 6-0:1.0: USB hub founde[0m
0.6 [runtime -> usb] hub 6-0:1.0: 1 port detectede[0m
0.6 [runtime -> usb] xhci_hcd c1:00.3: xHCI Host Controllere[0m
0.6 [runtime -> usb] xhci_hcd c1:00.3: new USB bus registered, assigned bus number 7e[0m
0.6 [runtime -> usb] xhci_hcd c1:00.3: hcc params 0x0128ffc5 hci version 0x120 quirks 0x0000000200000010e[0m
0.6 [runtime -> usb] xhci_hcd c1:00.3: xHCI Host Controllere[0m
0.6 [runtime -> usb] xhci_hcd c1:00.3: new USB bus registered, assigned bus number 8e[0m
0.6 [runtime -> usb] xhci_hcd c1:00.3: Host supports USB 3.1 Enhanced SuperSpeede[0m
0.6 [runtime -> usb] hub 7-0:1.0: USB hub founde[0m
0.6 [runtime -> usb] hub 7-0:1.0: 5 ports detectede[0m
0.6 [runtime -> usb] usb usb8: We don't know the algorithms for LPM for this host, disabling LPM.e[0m
0.6 [runtime -> usb] hub 8-0:1.0: USB hub founde[0m
0.6 [runtime -> usb] hub 8-0:1.0: 2 ports detectede[0m
0.6 [runtime -> usb] sched_clock: Marking stable (42411000, 10378000)->(54630000, -1841000)e[0m
0.6 [drivers -> platform] e[31mError: io_mem runtime -> nvme ->  cap=cap<invalid>e[0m
0.6 [runtime -> nvme] e[31mError: _ds_cap 96 cap=cap<invalid>e[0m
0.6 [runtime -> nvme] e[31mError: Uncaught exception of type 'Genode::Attached_dataspace::Invalid_dataspace'e[0m
0.6 [runtime -> nvme] e[34mWarning: abort called - thread: epe[0m
0.8 [runtime -> usb] usb 3-1: new full-speed USB device number 2 using xhci_hcde[0m
0.9 [runtime -> usb] usb 7-2: new high-speed USB device number 2 using xhci_hcde[0m
1.1 [runtime -> usb] hub 7-2:1.0: USB hub founde[0m
1.1 [runtime -> usb] hub 7-2:1.0: 4 ports detectede[0m
1.2 [runtime] child "usb_hid"e[0m
1.2 [runtime]   RAM quota:  11016Ke[0m
1.2 [runtime]   cap quota:  146e[0m
1.2 [runtime]   ELF binary: usb_hide[0m
1.2 [runtime]   priority:   2e[0m
1.2 [runtime -> usb_hid] SLUB: HWalign=64, Order=0-1, MinObjects=0, CPUs=1, Nodes=1e[0m
1.2 [runtime -> usb_hid] clocksource: dde_counter: mask: 0xffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 3526361616960 nse[0m
1.2 [runtime -> usb_hid] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 nse[0m
1.2 [runtime -> usb_hid] usbcore: registered new interface driver usbfse[0m
1.2 [runtime -> usb_hid] usbcore: registered new interface driver hube[0m
1.2 [runtime -> usb_hid] usbcore: registered new device driver usbe[0m
1.2 [runtime -> usb_hid] clocksource: Switched to clocksource dde_countere[0m
1.2 [runtime -> usb_hid] usbcore: registered new interface driver usbhide[0m
1.2 [runtime -> usb_hid] hid_core: USB HID core drivere[0m
1.2 [runtime -> usb_hid] sched_clock: Marking stable (0, 2372000)->(2825000, -453000)e[0m
1.2 [runtime -> usb] usb 8-2: new SuperSpeed Plus Gen 2x1 USB device number 2 using xhci_hcde[0m
1.2 [runtime -> usb_hid] hid-generic 0003:32AC:0002.0001: device has no listeners, quittinge[0m
1.2 [runtime -> usb] hub 8-2:1.0: USB hub founde[0m
1.2 [runtime -> usb] hub 8-2:1.0: 3 ports detectede[0m
1.3 [runtime -> usb] usb 7-3: new high-speed USB device number 3 using xhci_hcde[0m
1.5 [runtime -> usb] hub 7-3:1.0: USB hub founde[0m
1.5 [runtime -> usb] hub 7-3:1.0: 3 ports detectede[0m
1.6 [runtime -> usb] usb 8-1: new SuperSpeed USB device number 3 using xhci_hcde[0m
1.7 [runtime -> usb] usb 7-2.2: new high-speed USB device number 4 using xhci_hcde[0m
1.9 [runtime -> usb] usb 8-2.3: new SuperSpeed USB device number 4 using xhci_hcde[0m
2.0 [core] [init -> nitpicker] e[34mWarning: Gui (leitzentrale -> manager -> fader -> ) not enough RAM to preserve buffer content during resizee[0me[0m
2.0 [runtime -> usb] hub 8-2.3:1.0: USB hub founde[0m
2.0 [runtime -> usb] hub 8-2.3:1.0: 4 ports detectede[0m
2.1 [runtime -> usb] usb 7-4: new high-speed USB device number 5 using xhci_hcde[0m
2.3 [runtime -> usb] hub 7-4:1.0: USB hub founde[0m
2.3 [runtime -> usb] hub 7-4:1.0: 4 ports detectede[0m
2.3 [runtime -> usb] usb 7-3.2: new full-speed USB device number 6 using xhci_hcde[0m
2.4 [runtime -> usb] usb 7-3.2: unable to get BOS descriptor sete[0m
2.5 [runtime -> usb] usb 7-2.3: new high-speed USB device number 7 using xhci_hcde[0m
2.7 [runtime -> usb_hid] input: Framework Laptop 16 RGB Macropad as /devices/usb-7-6/0-0:1.0/0003:32AC:0013.0002/input/input0e[0m
2.7 [runtime -> usb] hub 7-2.3:1.0: USB hub founde[0m
2.7 [runtime -> usb] hub 7-2.3:1.0: 4 ports detectede[0m
2.8 [runtime -> usb_hid] Connected device: input0 (Framework Laptop 16 RGB Macropad at usb-usbbus-0/input0) e[0m
2.8 [runtime -> usb_hid] hid-generic 0003:32AC:0013.0002: input: USB HID v1.11 Keyboard [Framework Laptop 16 RGB Macropad] on usb-usbbus-0/input0e[0m
2.8 [runtime -> usb_hid] hid-generic 0003:32AC:0013.0003: device has no listeners, quittinge[0m
2.8 [runtime -> usb] usb 8-2.3.4: new SuperSpeed USB device number 5 using xhci_hcde[0m
2.8 [runtime -> usb_hid] input: Framework Laptop 16 RGB Macropad System Control as /devices/usb-7-6/0-0:1.2/0003:32AC:0013.0004/input/input1e[0m
2.8 [runtime -> usb_hid] Connected device: input1 (Framework Laptop 16 RGB Macropad System Control at usb-usbbus-0/input2) e[0m
2.8 [runtime -> usb_hid] input: Framework Laptop 16 RGB Macropad Consumer Control as /devices/usb-7-6/0-0:1.2/0003:32AC:0013.0004/input/input2e[0m
2.8 [runtime -> usb_hid] Connected device: input2 (Framework Laptop 16 RGB Macropad Consumer Control at usb-usbbus-0/input2) e[0m
2.8 [runtime -> usb_hid] input: Framework Laptop 16 RGB Macropad Wireless Radio Control as /devices/usb-7-6/0-0:1.2/0003:32AC:0013.0004/input/input3e[0m
2.8 [runtime -> usb_hid] Connected device: input3 (Framework Laptop 16 RGB Macropad Wireless Radio Control at usb-usbbus-0/input2) e[0m
2.8 [runtime -> usb_hid] input: Framework Laptop 16 RGB Macropad Keyboard as /devices/usb-7-6/0-0:1.2/0003:32AC:0013.0004/input/input4e[0m
2.8 [runtime -> usb_hid] Connected device: input4 (Framework Laptop 16 RGB Macropad Keyboard at usb-usbbus-0/input2) e[0m
2.8 [runtime -> usb_hid] hid-generic 0003:32AC:0013.0004: input: USB HID v1.11 Keyboard [Framework Laptop 16 RGB Macropad] on usb-usbbus-0/input2e[0m
2.8 [runtime -> usb_hid] hid-generic 0003:32AC:0013.0005: device has no listeners, quittinge[0m
2.9 [runtime -> usb] usb 7-5: new high-speed USB device number 8 using xhci_hcde[0m
3.2 [runtime -> usb] usb 7-4.1: new full-speed USB device number 9 using xhci_hcde[0m
3.3 [runtime -> usb] usb 7-2.3.1: new low-speed USB device number 10 using xhci_hcde[0m
3.5 [runtime -> usb] usb 7-4.2: new full-speed USB device number 11 using xhci_hcde[0m
3.6 [runtime -> usb_hid] input: Lite-On Technology Corp. ThinkPad USB Keyboard with TrackPoint as /devices/usb-7-10/0-0:1.0/0003:17EF:6009.0006/input/input5e[0m
3.6 [runtime -> usb] usb 7-4.2: unable to get BOS descriptor sete[0m
3.6 [runtime -> usb_hid] Connected device: input5 (Lite-On Technology Corp. ThinkPad USB Keyboard with TrackPoint at usb-usbbus-0/input0) e[0m
3.6 [runtime -> usb_hid] hid-generic 0003:17EF:6009.0006: input: USB HID v1.10 Keyboard [Lite-On Technology Corp. ThinkPad USB Keyboard with TrackPoint] on usb-usbbus-0/input0e[0m
3.6 [runtime -> usb_hid] input: Lite-On Technology Corp. ThinkPad USB Keyboard with TrackPoint Mouse as /devices/usb-7-10/0-0:1.1/0003:17EF:6009.0007/input/input6e[0m
3.7 [runtime -> usb_hid] Connected device: input6 (Lite-On Technology Corp. ThinkPad USB Keyboard with TrackPoint Mouse at usb-usbbus-0/input1) MOUSEe[0m
3.7 [runtime -> usb_hid] input: Lite-On Technology Corp. ThinkPad USB Keyboard with TrackPoint System Control as /devices/usb-7-10/0-0:1.1/0003:17EF:6009.0007/input/input7e[0m
3.7 [runtime -> usb] usb 7-2.3.3: new high-speed USB device number 12 using xhci_hcde[0m
3.7 [runtime -> usb_hid] Connected device: input7 (Lite-On Technology Corp. ThinkPad USB Keyboard with TrackPoint System Control at usb-usbbus-0/input1) e[0m
3.7 [runtime -> usb_hid] input: Lite-On Technology Corp. ThinkPad USB Keyboard with TrackPoint Consumer Control as /devices/usb-7-10/0-0:1.1/0003:17EF:6009.0007/input/input8e[0m
3.7 [runtime -> usb_hid] Connected device: input8 (Lite-On Technology Corp. ThinkPad USB Keyboard with TrackPoint Consumer Control at usb-usbbus-0/input1) e[0m
3.7 [runtime -> usb_hid] hid-generic 0003:17EF:6009.0007: input: USB HID v1.10 Mouse [Lite-On Technology Corp. ThinkPad USB Keyboard with TrackPoint] on usb-usbbus-0/input1e[0m
3.9 [runtime] child "usb-7-12"e[0m
3.9 [runtime]   RAM quota:  5896Ke[0m
3.9 [runtime]   cap quota:  66e[0m
3.9 [runtime]   ELF binary: usb_blocke[0m
3.9 [runtime]   priority:   3e[0m
3.9 [runtime]   provides service Blocke[0m
3.9 [runtime] child "usb-7-12.part"e[0m
3.9 [runtime]   RAM quota:  7944Ke[0m
3.9 [runtime]   cap quota:  66e[0m
3.9 [runtime]   ELF binary: part_blocke[0m
3.9 [runtime]   priority:   3e[0m
3.9 [runtime]   provides service Blocke[0m
3.9 [runtime -> usb_hid] input: Framework Laptop 16 Keyboard Module - ANSI as /devices/usb-7-11/0-0:1.0/0003:32AC:0012.0008/input/input9e[0m
3.9 [runtime] child "usb-7-12" announces service "Block"e[0m
3.9 [runtime -> usb-7-12.part] GPT Partition 1: LBA 40 (101 blocks) type: '21686148-6449-6e6f-744e-656564454649' name: 'BIOSBOOT'e[0m
3.9 [runtime -> usb-7-12.part] GPT Partition 2: LBA 141 (4515 blocks) type: 'c12a7328-f81f-11d2-ba4b-00a0c93ec93b' name: 'GRUB2'e[0m
3.9 [runtime -> usb-7-12.part] GPT Partition 3: LBA 6144 (2095104 blocks) type: '0fc63daf-8483-4772-8e79-3d69d8477de4' name: 'GENODE'e[0m
3.9 [runtime] child "usb-7-12.part" announces service "Block"e[0m
4.0 [runtime -> usb_hid] Connected device: input9 (Framework Laptop 16 Keyboard Module - ANSI at usb-usbbus-0/input0) e[0m
4.0 [runtime -> usb_hid] hid-generic 0003:32AC:0012.0008: input: USB HID v1.11 Keyboard [Framework Laptop 16 Keyboard Module - ANSI] on usb-usbbus-0/input0e[0m
4.0 [runtime -> usb] usb 7-2.3.3: reset high-speed USB device number 12 using xhci_hcde[0m
4.1 [runtime -> usb_hid] hid-generic 0003:32AC:0012.0009: device has no listeners, quittinge[0m
4.1 [runtime -> usb_hid] input: Framework Laptop 16 Keyboard Module - ANSI System Control as /devices/usb-7-11/0-0:1.2/0003:32AC:0012.000A/input/input10e[0m
4.2 [runtime -> usb_hid] Connected device: input10 (Framework Laptop 16 Keyboard Module - ANSI System Control at usb-usbbus-0/input2) e[0m
4.2 [runtime -> usb_hid] input: Framework Laptop 16 Keyboard Module - ANSI Consumer Control as /devices/usb-7-11/0-0:1.2/0003:32AC:0012.000A/input/input11e[0m
4.2 [runtime -> usb_hid] Connected device: input11 (Framework Laptop 16 Keyboard Module - ANSI Consumer Control at usb-usbbus-0/input2) e[0m
4.2 [runtime -> usb_hid] input: Framework Laptop 16 Keyboard Module - ANSI Wireless Radio Control as /devices/usb-7-11/0-0:1.2/0003:32AC:0012.000A/input/input12e[0m
4.2 [runtime -> usb_hid] Connected device: input12 (Framework Laptop 16 Keyboard Module - ANSI Wireless Radio Control at usb-usbbus-0/input2) e[0m
4.2 [runtime -> usb_hid] input: Framework Laptop 16 Keyboard Module - ANSI Keyboard as /devices/usb-7-11/0-0:1.2/0003:32AC:0012.000A/input/input13e[0m
4.2 [runtime -> usb_hid] Connected device: input13 (Framework Laptop 16 Keyboard Module - ANSI Keyboard at usb-usbbus-0/input2) e[0m
4.2 [runtime -> usb_hid] hid-generic 0003:32AC:0012.000A: input: USB HID v1.11 Keyboard [Framework Laptop 16 Keyboard Module - ANSI] on usb-usbbus-0/input2e[0m
4.2 [runtime -> usb_hid] hid-generic 0003:32AC:0012.000B: device has no listeners, quittinge[0m
8.2 [runtime -> runtime_view] e[34mWarning: attempt to handle the same signal context twice (nested)e[0m
12.0 [runtime] child "usb-7-12"e[0m
12.0 [runtime]   RAM quota:  5896Ke[0m
12.0 [runtime]   cap quota:  66e[0m
12.0 [runtime]   ELF binary: usb_blocke[0m
12.0 [runtime]   priority:   3e[0m
12.0 [runtime]   provides service Blocke[0m
12.0 [runtime] child "usb-7-12.part"e[0m
12.0 [runtime]   RAM quota:  7944Ke[0m
12.0 [runtime]   cap quota:  66e[0m
12.0 [runtime]   ELF binary: part_blocke[0m
12.0 [runtime]   priority:   3e[0m
12.0 [runtime]   provides service Blocke[0m
12.0 [runtime] child "usb-7-12.3.fs"e[0m
12.0 [runtime]   RAM quota:  73480Ke[0m
12.0 [runtime]   cap quota:  366e[0m
12.0 [runtime]   ELF binary: vfse[0m
12.0 [runtime]   priority:   3e[0m
12.0 [runtime]   provides service File_systeme[0m
12.0 [runtime] child "inspect"e[0m
12.0 [runtime]   RAM quota:  77576Ke[0m
12.0 [runtime]   cap quota:  966e[0m
12.0 [runtime]   ELF binary: inite[0m
12.0 [runtime]   priority:   2e[0m
12.1 [runtime] child "usb-7-12" announces service "Block"e[0m
12.1 [runtime -> usb-7-12.part] GPT Partition 1: LBA 40 (101 blocks) type: '21686148-6449-6e6f-744e-656564454649' name: 'BIOSBOOT'e[0m
12.1 [runtime -> usb-7-12.part] GPT Partition 2: LBA 141 (4515 blocks) type: 'c12a7328-f81f-11d2-ba4b-00a0c93ec93b' name: 'GRUB2'e[0m
12.1 [runtime -> usb-7-12.part] GPT Partition 3: LBA 6144 (2095104 blocks) type: '0fc63daf-8483-4772-8e79-3d69d8477de4' name: 'GENODE'e[0m
12.1 [runtime] child "usb-7-12.part" announces service "Block"e[0m
12.1 [runtime -> usb-7-12] e[34mWarning: SCSI command failure, expected tag=14, got tag=14 status=1e[0m
12.1 [runtime -> usb-7-12] e[31mError: Request_sense_response asc: 0x20 asq: 0x0e[0m
12.1 [runtime] child "usb-7-12.3.fs" announces service "File_system"e[0m
20.0 [leitzentrale -> nitpicker] e[34mWarning: Gui (wm -> runtime -> leitzentrale -> inspect) not enough RAM to preserve buffer content during resizee[0m

I don’t see anything too enlightening, but hopefully you can.

I’ll let you know the results of the new image soon!

[jjkarcher]

Unfortunately, this image did not boot on the FW16. It gets stuck on the splash image.

It boots fine on the ThinkPad Yoga, so it must be hardware-specific.

[Nos]

Wow, thanks from me too.
Unfortunately it does not boot on my framework16 (it reboots after showing the splash screen). It works on my Thinkpad X380 except the usb-network. I will try it again tomorrow evening.

[jjkarcher]

Actually, I have some good news - I tried the FW16 network adapter on the ThinkPad Yoga, and that did work!

(I couldn’t get my cheapo USB hub / network adapter to work on the first try, but that could be PEBKAC, and the ThinkPad WiFi works, so it’s not important.)

Thanks a million!

[jws]

@jjkarcher

Unfortunately, this image did not boot on the FW16. It gets stuck on the splash image.

Ah, my bad.

For one I left LOG=core enabled, which can be a problem on some systems, and also the image.elf.gz could be too large to boot now. We already encountered this problem on other machines (amongst others an AMD ThreadRipper based on).

So, I’ve made two new images:

❶ image (sig) with the NVMe and usb_net changes w/o LOG=core
❷ image (sig) like ❶ but without any pc_wifi firmware, i.e., the image.elf.gz is smaller but wifi will not work w/o firmware.

If both images do not work → back to the drawing board but that will have to wait until after FOSDEM (FYI, I have not checked if the images boot on hardware, as I am on the train right now, but they should).

[jws]

Thanks for testing - regarding the NVMe issue, your log contains a hint indeed:

@jjkarcher

[…]
0.6 [drivers -> platform] e[31mError: io_mem runtime -> nvme ->  cap=cap<invalid>e[0m
0.6 [runtime -> nvme] e[31mError: _ds_cap 96 cap=cap<invalid>e[0m
0.6 [runtime -> nvme] e[31mError: Uncaught exception of type 'Genode::Attached_dataspace::Invalid_dataspace'e[0m
0.6 [runtime -> nvme] e[34mWarning: abort called - thread: epe[0m
[…]

So the IOMEM capability the platform driver returns is invalid. Now the question is why does it return an invalid capability? I’ll prepare a more detailed debug image (but that might take a while).

[jjkarcher]

I tried the first image, and it worked great! Booted fine, and USB wired networking worked nicely.

Thanks a million! I hope you enjoyed FOSDEM. Can’t wait for the videos!

[jjkarcher]

You’re right, and here is another possible clue from higher up in the log:

0.3 [runtime] child "ram_fs" announces service "File_system"e[0m
0.3 [runtime -> boot_fb] using boot framebuffer: 2560x1600x32 @ 0x8800000000 type=1 pitch=10240 -> 2560x1600e[0m
0.3 [runtime -> nvme] e[31mError: DBGDI:2498e[0m

That doesn’t mean anything to me, but maybe it does to you.

[jws]

@jjkarcher

That doesn’t mean anything to me, but maybe it does to you.

That’s one of the debug messages I added and the corresponding DBGDO is printed after the Nvme::Driver object is constructed.

During yesterday’s train ride back I created a new image (sig) with @alex-ab’s help that should give more information about the reason why the platform driver may hand-out an invalid capability for the I/O memory session - we tried to provoke similar behavior synthetically to no avail.

[jjkarcher]

Thanks for the updated image! Here is the newest log:

[ snipped beginning - log too long ]
[0m0.0 [core] 591900K kernel memorye[0m
e[0m0.0 [core] Genode sculpt-25.10.1-12-gf2124d7715fe[0m
0.0 [core] 56512 MiB RAM and 63256 caps assigned to inite[0m
0.0 [runtime] parent providese[0m
0.0 [runtime]   service "ROM"e[0m
0.0 [runtime]   service "PD"e[0m
0.0 [runtime]   service "RM"e[0m
0.0 [runtime]   service "CPU"e[0m
0.0 [runtime]   service "LOG"e[0m
0.0 [runtime]   service "IO_MEM"e[0m
0.0 [runtime]   service "IO_PORT"e[0m
0.0 [runtime]   service "IRQ"e[0m
0.0 [runtime]   service "Gui"e[0m
0.0 [runtime]   service "Timer"e[0m
0.0 [runtime]   service "Block"e[0m
0.0 [runtime]   service "Report"e[0m
0.0 [runtime]   service "Platform"e[0m
0.0 [runtime] monitor readye[0m
0.0 [drivers -> acpi] Found HPET hw_id=0x10  vendor_id=0x1022 space_id=0x0 addr=0xfed00000 hpet_id=0x0e[0m
0.0 [drivers -> acpi] Found MADTe[0m
0.0 [drivers -> acpi] MADT IRQ 0 -> GSI 2 flags: 0e[0m
0.0 [drivers -> acpi] MADT IRQ 9 -> GSI 9 flags: 15e[0m
0.0 [drivers -> acpi] Found MCFGe[0m
0.0 [drivers -> acpi] MCFG BASE 0xe0000000 seg 0x0 bus 0x0-0xffe[0m
0.0 [drivers -> acpi] Found IVRSe[0m
0.0 [drivers -> acpi] XSDT OEM 'INSYDE', table id 'EDK2    ', revision 2, creator '    ' (16777235)e[0m
0.0 [drivers -> acpi] SMBIOSv2 table (entry point: 0x171000 structures: 0x58e75000)e[0m
0.2 [drivers -> pci_decode] e[34mWarning: Unsupported TPM2 device founde[0m
0.3 [runtime] parent providese[0m
0.3 [runtime]   service "VM"e[0m
0.3 [runtime]   service "Usb"e[0m
0.3 [runtime]   service "File_system"e[0m
0.3 [runtime]   service "Rtc"e[0m
0.3 [runtime]   service "TRACE"e[0m
0.3 [runtime]   service "Event"e[0m
0.3 [runtime]   service "Capture"e[0m
0.3 [runtime]   service "Gpu"e[0m
0.3 [runtime]   service "Pin_state"e[0m
0.3 [runtime]   service "Pin_control"e[0m
0.3 [runtime]   service "I2c"e[0m
0.3 [runtime]   service "Terminal"e[0m
0.3 [runtime] child "ps2"e[0m
0.3 [runtime]   RAM quota:  776Ke[0m
0.3 [runtime]   cap quota:  66e[0m
0.3 [runtime]   ELF binary: ps2e[0m
0.3 [runtime]   priority:   2e[0m
0.3 [runtime] child "boot_fb"e[0m
0.3 [runtime]   RAM quota:  16776Ke[0m
0.3 [runtime]   cap quota:  66e[0m
0.3 [runtime]   ELF binary: boot_fbe[0m
0.3 [runtime]   priority:   2e[0m
0.3 [runtime] child "usb"e[0m
0.3 [runtime]   RAM quota:  16136Ke[0m
0.3 [runtime]   cap quota:  166e[0m
0.3 [runtime]   ELF binary: usbe[0m
0.3 [runtime]   priority:   2e[0m
0.3 [runtime]   provides service Usbe[0m
0.3 [runtime] child "nvme"e[0m
0.3 [runtime]   RAM quota:  7944Ke[0m
0.3 [runtime]   cap quota:  66e[0m
0.3 [runtime]   ELF binary: nvmee[0m
0.3 [runtime]   priority:   3e[0m
0.3 [runtime]   provides service Blocke[0m
0.3 [runtime] child "runtime_view"e[0m
0.3 [runtime]   RAM quota:  53000Ke[0m
0.3 [runtime]   cap quota:  296e[0m
0.3 [runtime]   ELF binary: menu_viewe[0m
0.3 [runtime]   priority:   2e[0m
0.3 [runtime] child "ram_fs"e[0m
0.3 [runtime]   RAM quota:  776Ke[0m
0.3 [runtime]   cap quota:  266e[0m
0.3 [runtime]   ELF binary: vfse[0m
0.3 [runtime]   priority:   2e[0m
0.3 [runtime]   provides service File_systeme[0m
0.3 [runtime] child "ram_fs" announces service "File_system"e[0m
0.3 [runtime -> ps2] i8042: no controller detectede[0m
0.3 [runtime -> boot_fb] using boot framebuffer: 2560x1600x32 @ 0x8800000000 type=1 pitch=10240 -> 2560x1600e[0m
0.3 [runtime -> nvme] e[31mError: DBGDI:2498e[0m
0.5 [runtime] child "usb" announces service "Usb"e[0m
0.5 [runtime -> usb] SLUB: HWalign=64, Order=0-1, MinObjects=0, CPUs=1, Nodes=1e[0m
0.5 [runtime -> usb] NR_IRQS: 4352, nr_irqs: 4352, preallocated irqs: 256e[0m
0.5 [runtime -> usb] clocksource: dde_counter: mask: 0xffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 3526361616960 nse[0m
0.5 [runtime -> usb] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 nse[0m
0.5 [runtime -> usb] usbcore: registered new interface driver usbfse[0m
0.5 [runtime -> usb] usbcore: registered new interface driver hube[0m
0.6 [runtime -> usb] usbcore: registered new device driver usbe[0m
0.6 [runtime -> usb] clocksource: Switched to clocksource dde_countere[0m
0.6 [runtime -> usb] usbcore: registered new interface driver genodee[0m
0.6 [runtime -> usb] xhci_hcd c3:00.4: xHCI Host Controllere[0m
0.6 [runtime -> usb] xhci_hcd c3:00.4: new USB bus registered, assigned bus number 1e[0m
0.6 [runtime -> usb] xhci_hcd c3:00.4: hcc params 0x0110ffc5 hci version 0x120 quirks 0x0000000200000010e[0m
0.6 [runtime -> usb] xhci_hcd c3:00.4: xHCI Host Controllere[0m
0.6 [runtime -> usb] xhci_hcd c3:00.4: new USB bus registered, assigned bus number 2e[0m
0.6 [runtime -> usb] xhci_hcd c3:00.4: Host supports USB 3.1 Enhanced SuperSpeede[0m
0.6 [runtime -> usb] hub 1-0:1.0: USB hub founde[0m
0.6 [runtime -> usb] hub 1-0:1.0: 1 port detectede[0m
0.6 [runtime -> usb] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.e[0m
0.6 [runtime -> usb] hub 2-0:1.0: USB hub founde[0m
0.6 [runtime -> usb] hub 2-0:1.0: 1 port detectede[0m
0.6 [runtime -> usb] xhci_hcd c3:00.3: xHCI Host Controllere[0m
0.6 [runtime -> usb] xhci_hcd c3:00.3: new USB bus registered, assigned bus number 3e[0m
0.6 [runtime -> usb] xhci_hcd c3:00.3: hcc params 0x0110ffc5 hci version 0x120 quirks 0x0000000200000010e[0m
0.6 [runtime -> usb] xhci_hcd c3:00.3: xHCI Host Controllere[0m
0.6 [runtime -> usb] xhci_hcd c3:00.3: new USB bus registered, assigned bus number 4e[0m
0.6 [runtime -> usb] xhci_hcd c3:00.3: Host supports USB 3.1 Enhanced SuperSpeede[0m
0.6 [runtime -> usb] hub 3-0:1.0: USB hub founde[0m
0.6 [runtime -> usb] hub 3-0:1.0: 1 port detectede[0m
0.6 [runtime -> usb] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.e[0m
0.6 [runtime -> usb] hub 4-0:1.0: USB hub founde[0m
0.6 [runtime -> usb] hub 4-0:1.0: 1 port detectede[0m
0.6 [runtime -> usb] xhci_hcd c1:00.4: xHCI Host Controllere[0m
0.6 [runtime -> usb] xhci_hcd c1:00.4: new USB bus registered, assigned bus number 5e[0m
0.6 [runtime -> usb] xhci_hcd c1:00.4: hcc params 0x0110ffc5 hci version 0x120 quirks 0x0000000200000010e[0m
0.6 [runtime -> usb] xhci_hcd c1:00.4: xHCI Host Controllere[0m
0.6 [runtime -> usb] xhci_hcd c1:00.4: new USB bus registered, assigned bus number 6e[0m
0.6 [runtime -> usb] xhci_hcd c1:00.4: Host supports USB 3.1 Enhanced SuperSpeede[0m
0.6 [runtime -> usb] hub 5-0:1.0: USB hub founde[0m
0.6 [runtime -> usb] hub 5-0:1.0: 1 port detectede[0m
0.6 [runtime -> usb] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.e[0m
0.6 [runtime -> usb] hub 6-0:1.0: USB hub founde[0m
0.6 [runtime -> usb] hub 6-0:1.0: 1 port detectede[0m
0.6 [runtime -> usb] xhci_hcd c1:00.3: xHCI Host Controllere[0m
0.6 [runtime -> usb] xhci_hcd c1:00.3: new USB bus registered, assigned bus number 7e[0m
0.6 [runtime -> usb] xhci_hcd c1:00.3: hcc params 0x0128ffc5 hci version 0x120 quirks 0x0000000200000010e[0m
0.6 [runtime -> usb] xhci_hcd c1:00.3: xHCI Host Controllere[0m
0.6 [runtime -> usb] xhci_hcd c1:00.3: new USB bus registered, assigned bus number 8e[0m
0.6 [runtime -> usb] xhci_hcd c1:00.3: Host supports USB 3.1 Enhanced SuperSpeede[0m
0.6 [runtime -> usb] hub 7-0:1.0: USB hub founde[0m
0.6 [runtime -> usb] hub 7-0:1.0: 5 ports detectede[0m
0.6 [runtime -> usb] usb usb8: We don't know the algorithms for LPM for this host, disabling LPM.e[0m
0.6 [runtime -> usb] hub 8-0:1.0: USB hub founde[0m
0.6 [runtime -> usb] hub 8-0:1.0: 2 ports detectede[0m
0.6 [runtime -> usb] sched_clock: Marking stable (51887000, 9257000)->(62836000, -1692000)e[0m
0.6 [drivers -> platform] e[31mError: io_mem runtime -> nvme ->  cap=cap<invalid>e[0m
0.6 [runtime -> nvme] e[31mError: _ds_cap 96 cap=cap<invalid>e[0m
0.6 [runtime -> nvme] e[31mError: Uncaught exception of type 'Genode::Attached_dataspace::Invalid_dataspace'e[0m
0.6 [runtime -> nvme] e[34mWarning: abort called - thread: epe[0m
0.8 [runtime -> usb] usb 3-1: new full-speed USB device number 2 using xhci_hcde[0m
0.9 [runtime -> usb] usb 7-2: new high-speed USB device number 2 using xhci_hcde[0m
1.0 [runtime -> usb] hub 7-2:1.0: USB hub founde[0m
1.1 [runtime -> usb] hub 7-2:1.0: 4 ports detectede[0m
1.2 [runtime] child "usb_hid"e[0m
1.2 [runtime]   RAM quota:  11016Ke[0m
1.2 [runtime]   cap quota:  146e[0m
1.2 [runtime]   ELF binary: usb_hide[0m
1.2 [runtime]   priority:   2e[0m
1.2 [runtime -> usb_hid] SLUB: HWalign=64, Order=0-1, MinObjects=0, CPUs=1, Nodes=1e[0m
1.2 [runtime -> usb_hid] clocksource: dde_counter: mask: 0xffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 3526361616960 nse[0m
1.2 [runtime -> usb_hid] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 nse[0m
1.2 [runtime -> usb_hid] usbcore: registered new interface driver usbfse[0m
1.2 [runtime -> usb_hid] usbcore: registered new interface driver hube[0m
1.2 [runtime -> usb_hid] usbcore: registered new device driver usbe[0m
1.2 [runtime -> usb_hid] clocksource: Switched to clocksource dde_countere[0m
1.2 [runtime -> usb_hid] usbcore: registered new interface driver usbhide[0m
1.2 [runtime -> usb_hid] hid_core: USB HID core drivere[0m
1.2 [runtime -> usb_hid] sched_clock: Marking stable (0, 2602000)->(3095000, -493000)e[0m
1.2 [runtime -> usb] usb 8-2: new SuperSpeed Plus Gen 2x1 USB device number 2 using xhci_hcde[0m
1.2 [runtime -> usb_hid] hid-generic 0003:32AC:0002.0001: device has no listeners, quittinge[0m
1.2 [runtime -> usb] hub 8-2:1.0: USB hub founde[0m
1.2 [runtime -> usb] hub 8-2:1.0: 3 ports detectede[0m
1.3 [runtime -> usb] usb 7-3: new high-speed USB device number 3 using xhci_hcde[0m
1.5 [runtime -> usb] hub 7-3:1.0: USB hub founde[0m
1.5 [runtime -> usb] hub 7-3:1.0: 3 ports detectede[0m
1.6 [runtime -> usb] usb 7-2.1: new high-speed USB device number 4 using xhci_hcde[0m
1.8 [runtime -> usb] hub 7-2.1:1.0: USB hub founde[0m
1.8 [runtime -> usb] hub 7-2.1:1.0: 4 ports detectede[0m
1.8 [runtime -> usb] usb 8-1: new SuperSpeed USB device number 3 using xhci_hcde[0m
2.0 [core] ", ram_quota=3726, cap_quota=2'e[0m
2.0 [core] e[31mError: _create_session:33: args: 'base=0x8800000000, size=0xfa0000, wc=yes, diag=0, label="init -> runtime -> boot_fb -> ", ram_quota=3726, cap_quota=2'e[0m
2.0 [core] [init -> nitpicker] e[34mWarning: Gui (leitzentrale -> manager -> fader -> ) not enough RAM to preserve buffer content during resizee[0me[0m
2.0 [core] e[31mError: _create_session:33: args: 'base=0xec304000, size=0x1000, wc=no, diag=0, label="init -> drivers -> platform -> ", ram_quota=3726, cap_quota=2'e[0m
2.0 [core] e[31mError: _create_session:33: args: 'base=0xec304000, size=0x1000, wc=no, diag=0, label="init -> drivers -> platform -> ", ram_quota=3726, cap_quota=2'e[0m
2.0 [core] e[31mError: _create_session:33: args: 'base=0x90700000, size=0x100000, wc=no, diag=0, label="init -> drivers -> platform -> ", ram_quota=3726, cap_quota=2'e[0m
2.0 [core] e[31mError: _create_session:33: args: 'base=0xec304000, size=0x1000, wc=no, diag=0, label="init -> drivers -> platform -> ", ram_quota=3726, cap_quota=2'e[0m
2.0 [core] e[31mError: _create_session:33: args: 'base=0xec303000, size=0x1000, wc=no, diag=0, label="init -> drivers -> platform -> ", ram_quota=3726, cap_quota=2'e[0m
2.0 [core] e[31mError: _create_session:33: args: 'base=0xec303000, size=0x1000, wc=no, diag=0, label="init -> drivers -> platform -> ", ram_quota=3726, cap_quota=2'e[0m
2.0 [core] e[31mError: _create_session:33: args: 'base=0x90600000, size=0x100000, wc=no, diag=0, label="init -> drivers -> platform -> ", ram_quota=3726, cap_quota=2'e[0m
2.0 [core] e[31mError: _create_session:33: args: 'base=0xec303000, size=0x1000, wc=no, diag=0, label="init -> drivers -> platform -> ", ram_quota=3726, cap_quota=2'e[0m
2.0 [core] e[31mError: _create_session:33: args: 'base=0xec104000, size=0x1000, wc=no, diag=0, label="init -> drivers -> platform -> ", ram_quota=3726, cap_quota=2'e[0m
2.0 [core] e[31mError: _create_session:33: args: 'base=0xec104000, size=0x1000, wc=no, diag=0, label="init -> drivers -> platform -> ", ram_quota=3726, cap_quota=2'e[0m
2.0 [core] e[31mError: _create_session:33: args: 'base=0x90300000, size=0x100000, wc=no, diag=0, label="init -> drivers -> platform -> ", ram_quota=3726, cap_quota=2'e[0m
2.0 [core] e[31mError: _create_session:33: args: 'base=0xec104000, size=0x1000, wc=no, diag=0, label="init -> drivers -> platform -> ", ram_quota=3726, cap_quota=2'e[0m
2.0 [core] e[31mError: _create_session:33: args: 'base=0xec103000, size=0x1000, wc=no, diag=0, label="init -> drivers -> platform -> ", ram_quota=3726, cap_quota=2'e[0m
2.0 [core] e[31mError: _create_session:33: args: 'base=0xec103000, size=0x1000, wc=no, diag=0, label="init -> drivers -> platform -> ", ram_quota=3726, cap_quota=2'e[0m
2.0 [core] e[31mError: _create_session:33: args: 'base=0x90200000, size=0x100000, wc=no, diag=0, label="init -> drivers -> platform -> ", ram_quota=3726, cap_quota=2'e[0m
2.0 [core] e[31mError: _create_session:33: args: 'base=0xec103000, size=0x1000, wc=no, diag=0, label="init -> drivers -> platform -> ", ram_quota=3726, cap_quota=2'e[0m
2.0 [core] e[31mError: _create_session:33: args: 'base=0xe001a000, size=0x1000, wc=no, diag=0, label="init -> drivers -> platform -> ", ram_quota=3726, cap_quota=2'e[0m
2.0 [core] e[31mError: _create_session:33: args: 'base=0xe001a000, size=0x1000, wc=no, diag=0, label="init -> drivers -> platform -> ", ram_quota=3726, cap_quota=2'e[0m
2.0 [runtime -> usb] usb 7-4: new high-speed USB device number 5 using xhci_hcde[0m
2.2 [runtime -> usb] hub 7-4:1.0: USB hub founde[0m
2.2 [runtime -> usb] hub 7-4:1.0: 4 ports detectede[0m
2.2 [runtime -> usb] usb 7-2.2: new high-speed USB device number 6 using xhci_hcde[0m
2.5 [runtime -> usb] usb 7-3.2: new full-speed USB device number 7 using xhci_hcde[0m
2.6 [runtime -> usb] usb 7-3.2: unable to get BOS descriptor sete[0m
2.7 [runtime -> usb] usb 7-2.1.1: new full-speed USB device number 8 using xhci_hcde[0m
2.8 [runtime -> usb_hid] input: Framework Laptop 16 RGB Macropad as /devices/usb-7-7/0-0:1.0/0003:32AC:0013.0002/input/input0e[0m
2.9 [runtime -> usb_hid] Connected device: input0 (Framework Laptop 16 RGB Macropad at usb-usbbus-0/input0) e[0m
2.9 [runtime -> usb_hid] hid-generic 0003:32AC:0013.0002: input: USB HID v1.11 Keyboard [Framework Laptop 16 RGB Macropad] on usb-usbbus-0/input0e[0m
2.9 [runtime -> usb_hid] hid-generic 0003:32AC:0013.0003: device has no listeners, quittinge[0m
2.9 [runtime -> usb_hid] input: Framework Laptop 16 RGB Macropad System Control as /devices/usb-7-7/0-0:1.2/0003:32AC:0013.0004/input/input1e[0m
3.0 [runtime -> usb_hid] Connected device: input1 (Framework Laptop 16 RGB Macropad System Control at usb-usbbus-0/input2) e[0m
3.0 [runtime -> usb_hid] input: Framework Laptop 16 RGB Macropad Consumer Control as /devices/usb-7-7/0-0:1.2/0003:32AC:0013.0004/input/input2e[0m
3.0 [runtime -> usb_hid] Connected device: input2 (Framework Laptop 16 RGB Macropad Consumer Control at usb-usbbus-0/input2) e[0m
3.0 [runtime -> usb_hid] input: Framework Laptop 16 RGB Macropad Wireless Radio Control as /devices/usb-7-7/0-0:1.2/0003:32AC:0013.0004/input/input3e[0m
3.0 [runtime -> usb_hid] Connected device: input3 (Framework Laptop 16 RGB Macropad Wireless Radio Control at usb-usbbus-0/input2) e[0m
3.0 [runtime -> usb_hid] input: Framework Laptop 16 RGB Macropad Keyboard as /devices/usb-7-7/0-0:1.2/0003:32AC:0013.0004/input/input4e[0m
3.0 [runtime -> usb_hid] Connected device: input4 (Framework Laptop 16 RGB Macropad Keyboard at usb-usbbus-0/input2) e[0m
3.0 [runtime -> usb_hid] hid-generic 0003:32AC:0013.0004: input: USB HID v1.11 Keyboard [Framework Laptop 16 RGB Macropad] on usb-usbbus-0/input2e[0m
3.0 [runtime -> usb_hid] hid-generic 0003:32AC:0013.0005: device has no listeners, quittinge[0m
3.1 [runtime -> usb] usb 7-5: new high-speed USB device number 9 using xhci_hcde[0m
3.3 [runtime -> usb] usb 7-4.1: new full-speed USB device number 10 using xhci_hcde[0m
3.6 [runtime -> usb] usb 7-2.1.2: new high-speed USB device number 11 using xhci_hcde[0m
3.9 [runtime -> usb] usb 7-4.2: new full-speed USB device number 12 using xhci_hcde[0m
4.0 [runtime -> usb] usb 7-4.2: unable to get BOS descriptor sete[0m
4.2 [runtime -> usb] usb 7-2.1.3: new high-speed USB device number 13 using xhci_hcde[0m
4.3 [runtime -> usb_hid] input: Framework Laptop 16 Keyboard Module - ANSI as /devices/usb-7-12/0-0:1.0/0003:32AC:0012.0006/input/input5e[0m
4.3 [runtime -> usb_hid] Connected device: input5 (Framework Laptop 16 Keyboard Module - ANSI at usb-usbbus-0/input0) e[0m
4.3 [runtime -> usb_hid] hid-generic 0003:32AC:0012.0006: input: USB HID v1.11 Keyboard [Framework Laptop 16 Keyboard Module - ANSI] on usb-usbbus-0/input0e[0m
4.3 [runtime -> usb_hid] hid-generic 0003:32AC:0012.0007: device has no listeners, quittinge[0m
4.4 [runtime -> usb_hid] input: Framework Laptop 16 Keyboard Module - ANSI System Control as /devices/usb-7-12/0-0:1.2/0003:32AC:0012.0008/input/input6e[0m
4.4 [runtime -> usb_hid] Connected device: input6 (Framework Laptop 16 Keyboard Module - ANSI System Control at usb-usbbus-0/input2) e[0m
4.4 [runtime -> usb_hid] input: Framework Laptop 16 Keyboard Module - ANSI Consumer Control as /devices/usb-7-12/0-0:1.2/0003:32AC:0012.0008/input/input7e[0m
4.4 [runtime -> usb_hid] Connected device: input7 (Framework Laptop 16 Keyboard Module - ANSI Consumer Control at usb-usbbus-0/input2) e[0m
4.4 [runtime -> usb_hid] input: Framework Laptop 16 Keyboard Module - ANSI Wireless Radio Control as /devices/usb-7-12/0-0:1.2/0003:32AC:0012.0008/input/input8e[0m
4.4 [runtime -> usb_hid] Connected device: input8 (Framework Laptop 16 Keyboard Module - ANSI Wireless Radio Control at usb-usbbus-0/input2) e[0m
4.4 [runtime -> usb_hid] input: Framework Laptop 16 Keyboard Module - ANSI Keyboard as /devices/usb-7-12/0-0:1.2/0003:32AC:0012.0008/input/input9e[0m
4.4 [runtime -> usb_hid] Connected device: input9 (Framework Laptop 16 Keyboard Module - ANSI Keyboard at usb-usbbus-0/input2) e[0m
4.4 [runtime -> usb_hid] hid-generic 0003:32AC:0012.0008: input: USB HID v1.11 Keyboard [Framework Laptop 16 Keyboard Module - ANSI] on usb-usbbus-0/input2e[0m
4.4 [runtime -> usb_hid] hid-generic 0003:32AC:0012.0009: device has no listeners, quittinge[0m
4.4 [runtime] child "usb-7-13"e[0m
4.4 [runtime]   RAM quota:  5896Ke[0m
4.4 [runtime]   cap quota:  66e[0m
4.4 [runtime]   ELF binary: usb_blocke[0m
4.4 [runtime]   priority:   3e[0m
4.4 [runtime]   provides service Blocke[0m
4.4 [runtime] child "usb-7-13.part"e[0m
4.4 [runtime]   RAM quota:  7944Ke[0m
4.4 [runtime]   cap quota:  66e[0m
4.4 [runtime]   ELF binary: part_blocke[0m
4.4 [runtime]   priority:   3e[0m
4.4 [runtime]   provides service Blocke[0m
4.5 [runtime] child "usb-7-13" announces service "Block"e[0m
4.5 [runtime -> usb-7-13.part] GPT Partition 1: LBA 40 (101 blocks) type: '21686148-6449-6e6f-744e-656564454649' name: 'BIOSBOOT'e[0m
4.5 [runtime -> usb-7-13.part] GPT Partition 2: LBA 141 (4515 blocks) type: 'c12a7328-f81f-11d2-ba4b-00a0c93ec93b' name: 'GRUB2'e[0m
4.5 [runtime -> usb-7-13.part] GPT Partition 3: LBA 6144 (2045952 blocks) type: '0fc63daf-8483-4772-8e79-3d69d8477de4' name: 'GENODE'e[0m
4.5 [runtime] child "usb-7-13.part" announces service "Block"e[0m
4.6 [runtime -> usb] usb 7-2.1.4: new low-speed USB device number 14 using xhci_hcde[0m
5.0 [runtime -> usb] usb 7-2.1.3: reset high-speed USB device number 13 using xhci_hcde[0m
5.2 [runtime -> usb_hid] input: Lite-On Technology Corp. ThinkPad USB Keyboard with TrackPoint as /devices/usb-7-14/0-0:1.0/0003:17EF:6009.000A/input/input10e[0m
5.3 [runtime -> usb_hid] Connected device: input10 (Lite-On Technology Corp. ThinkPad USB Keyboard with TrackPoint at usb-usbbus-0/input0) e[0m
5.3 [runtime -> usb_hid] hid-generic 0003:17EF:6009.000A: input: USB HID v1.10 Keyboard [Lite-On Technology Corp. ThinkPad USB Keyboard with TrackPoint] on usb-usbbus-0/input0e[0m
5.3 [runtime -> usb_hid] input: Lite-On Technology Corp. ThinkPad USB Keyboard with TrackPoint Mouse as /devices/usb-7-14/0-0:1.1/0003:17EF:6009.000B/input/input11e[0m
5.3 [runtime -> usb_hid] Connected device: input11 (Lite-On Technology Corp. ThinkPad USB Keyboard with TrackPoint Mouse at usb-usbbus-0/input1) MOUSEe[0m
5.3 [runtime -> usb_hid] input: Lite-On Technology Corp. ThinkPad USB Keyboard with TrackPoint System Control as /devices/usb-7-14/0-0:1.1/0003:17EF:6009.000B/input/input12e[0m
5.3 [runtime -> usb_hid] Connected device: input12 (Lite-On Technology Corp. ThinkPad USB Keyboard with TrackPoint System Control at usb-usbbus-0/input1) e[0m
5.3 [runtime -> usb_hid] input: Lite-On Technology Corp. ThinkPad USB Keyboard with TrackPoint Consumer Control as /devices/usb-7-14/0-0:1.1/0003:17EF:6009.000B/input/input13e[0m
5.3 [runtime -> usb_hid] Connected device: input13 (Lite-On Technology Corp. ThinkPad USB Keyboard with TrackPoint Consumer Control at usb-usbbus-0/input1) e[0m
5.3 [runtime -> usb_hid] hid-generic 0003:17EF:6009.000B: input: USB HID v1.10 Mouse [Lite-On Technology Corp. ThinkPad USB Keyboard with TrackPoint] on usb-usbbus-0/input1e[0m
10.6 [runtime -> runtime_view] e[34mWarning: attempt to handle the same signal context twice (nested)e[0m
14.7 [runtime] child "usb-7-13"e[0m
14.7 [runtime]   RAM quota:  5896Ke[0m
14.7 [runtime]   cap quota:  66e[0m
14.7 [runtime]   ELF binary: usb_blocke[0m
14.7 [runtime]   priority:   3e[0m
14.7 [runtime]   provides service Blocke[0m
14.7 [runtime] child "usb-7-13.part"e[0m
14.7 [runtime]   RAM quota:  7944Ke[0m
14.7 [runtime]   cap quota:  66e[0m
14.7 [runtime]   ELF binary: part_blocke[0m
14.7 [runtime]   priority:   3e[0m
14.7 [runtime]   provides service Blocke[0m
14.7 [runtime] child "usb-7-13.3.fs"e[0m
14.7 [runtime]   RAM quota:  73480Ke[0m
14.7 [runtime]   cap quota:  366e[0m
14.7 [runtime]   ELF binary: vfse[0m
14.7 [runtime]   priority:   3e[0m
14.7 [runtime]   provides service File_systeme[0m
14.7 [runtime] child "prepare"e[0m
14.7 [runtime]   RAM quota:  102152Ke[0m
14.7 [runtime]   cap quota:  766e[0m
14.7 [runtime]   ELF binary: inite[0m
14.7 [runtime]   priority:   3e[0m
14.7 [runtime] child "depot"e[0m
14.7 [runtime]   RAM quota:  1800Ke[0m
14.7 [runtime]   cap quota:  66e[0m
14.7 [runtime]   ELF binary: chroote[0m
14.7 [runtime]   priority:   3e[0m
14.7 [runtime]   provides service File_systeme[0m
14.8 [runtime] child "usb-7-13" announces service "Block"e[0m
14.8 [runtime -> usb-7-13.part] GPT Partition 1: LBA 40 (101 blocks) type: '21686148-6449-6e6f-744e-656564454649' name: 'BIOSBOOT'e[0m
14.8 [runtime -> usb-7-13.part] GPT Partition 2: LBA 141 (4515 blocks) type: 'c12a7328-f81f-11d2-ba4b-00a0c93ec93b' name: 'GRUB2'e[0m
14.8 [runtime -> usb-7-13.part] GPT Partition 3: LBA 6144 (2045952 blocks) type: '0fc63daf-8483-4772-8e79-3d69d8477de4' name: 'GENODE'e[0m
14.8 [runtime] child "usb-7-13.part" announces service "Block"e[0m
14.8 [runtime -> usb-7-13] e[34mWarning: SCSI command failure, expected tag=14, got tag=14 status=1e[0m
14.8 [runtime -> usb-7-13] e[31mError: Request_sense_response asc: 0x20 asq: 0x0e[0m
14.8 [runtime] child "usb-7-13.3.fs" announces service "File_system"e[0m
14.8 [runtime] child "depot" announces service "File_system"e[0m
14.9 [runtime -> prepare -> bash] e[31mError: no plugin found for fcntl(3)e[0m
14.9 [runtime -> prepare -> bash] e[31mError: no plugin found for fcntl(4)e[0m
14.9 [runtime -> prepare -> bash] e[31mError: no plugin found for fcntl(5)e[0m
14.9 [runtime -> prepare -> bash] e[31mError: no plugin found for fcntl(6)e[0m
14.9 [runtime -> prepare -> bash] e[31mError: no plugin found for fcntl(7)e[0m
14.9 [runtime -> prepare -> bash] e[31mError: no plugin found for fcntl(8)e[0m
14.9 [runtime -> prepare -> bash] e[31mError: no plugin found for fcntl(9)e[0m
14.9 [runtime -> prepare -> bash] e[31mError: no plugin found for fcntl(10)e[0m
14.9 [runtime -> prepare -> bash] e[31mError: no plugin found for fcntl(11)e[0m
14.9 [runtime -> prepare -> bash] e[31mError: no plugin found for fcntl(12)e[0m
14.9 [runtime -> prepare -> bash] e[31mError: no plugin found for fcntl(13)e[0m
14.9 [runtime -> prepare -> bash] e[31mError: no plugin found for fcntl(14)e[0m
14.9 [runtime -> prepare -> bash] e[31mError: no plugin found for fcntl(15)e[0m
14.9 [runtime -> prepare -> bash] e[31mError: no plugin found for fcntl(16)e[0m
14.9 [runtime -> prepare -> bash] e[31mError: no plugin found for fcntl(17)e[0m
14.9 [runtime -> prepare -> bash] e[31mError: no plugin found for fcntl(18)e[0m
14.9 [runtime -> prepare -> bash] e[31mError: no plugin found for fcntl(19)e[0m
15.3 [runtime] child "prepare" exited with exit value 0e[0m
15.3 [runtime] child "launcher_query"e[0m
15.3 [runtime]   RAM quota:  1800Ke[0m
15.3 [runtime]   cap quota:  166e[0m
15.3 [runtime]   ELF binary: fs_querye[0m
15.3 [runtime]   priority:   3e[0m
15.3 [runtime] child "depot_rom"e[0m
15.3 [runtime]   RAM quota:  24328Ke[0m
15.3 [runtime]   cap quota:  166e[0m
15.3 [runtime]   ELF binary: cached_fs_rome[0m
15.3 [runtime]   priority:   3e[0m
15.3 [runtime]   provides service ROMe[0m
15.3 [runtime] child "dynamic_depot_rom"e[0m
15.3 [runtime]   RAM quota:  7944Ke[0m
15.3 [runtime]   cap quota:  166e[0m
15.3 [runtime]   ELF binary: fs_rome[0m
15.3 [runtime]   priority:   3e[0m
15.3 [runtime]   provides service ROMe[0m
15.3 [runtime] child "depot_query"e[0m
15.3 [runtime]   RAM quota:  1800Ke[0m
15.3 [runtime]   cap quota:  166e[0m
15.3 [runtime]   ELF binary: depot_querye[0m
15.3 [runtime]   priority:   3e[0m
15.3 [runtime] child "depot_rom" announces service "ROM"e[0m
15.3 [runtime] child "dynamic_depot_rom" announces service "ROM"e[0m
16.0 [runtime] child "inspect"e[0m
16.0 [runtime]   RAM quota:  77576Ke[0m
16.0 [runtime]   cap quota:  966e[0m
16.0 [runtime]   ELF binary: inite[0m
16.0 [runtime]   priority:   2e[0m
19.3 [leitzentrale -> nitpicker] e[34mWarning: Gui (wm -> runtime -> leitzentrale -> inspect) not enough RAM to preserve buffer content during resizee[0m

There are some new messages - hopefully something useful. Thanks again!

[Nos]

Many thanks! I have similar problems with NVME. But since my other device with NVME works great, this is not so important to me. I hope that with my shortened excerpt from the reports/log I can still help.

$ grep -5 nvme mylog
0.0 [core]  ROM: [00000000579dc000,0000000057a5c900) monitor
0.0 [core]  ROM: [0000000055c95000,0000000055cec128) ncurses.lib.so
0.0 [core]  ROM: [0000000055cf6000,0000000055d8ab98) nic_router
0.0 [core]  ROM: [0000000055036000,0000000055037e76) nic_router.xsd
0.0 [core]  ROM: [00000000551c0000,0000000055241670) nitpicker
0.0 [core]  ROM: [0000000056409000,0000000056449e20) nvme
0.0 [core]  ROM: [0000000057f11000,0000000057f3fef0) part_block
0.0 [core]  ROM: [0000000057b83000,0000000057ed1228) pc_intel_fb
0.0 [core]  ROM: [0000000054e97000,0000000055035228) pc_nic
0.0 [core]  ROM: [000000005668d000,000000005673ae00) pc_platform
0.0 [core]  ROM: [0000000055038000,00000000551a9e10) pc_usb_host
--
0.3 [runtime]   RAM quota:  16136K
0.3 [runtime]   cap quota:  166
0.3 [runtime]   ELF binary: usb
0.3 [runtime]   priority:   2
0.3 [runtime]   provides service Usb
0.3 [runtime] child "nvme"
0.3 [runtime]   RAM quota:  7944K
0.3 [runtime]   cap quota:  66
0.3 [runtime]   ELF binary: nvme
0.3 [runtime]   priority:   3
0.3 [runtime]   provides service Block
0.3 [runtime] child "runtime_view"
0.3 [runtime]   RAM quota:  53000K
0.3 [runtime]   cap quota:  296
--
0.3 [runtime]   priority:   2
0.3 [runtime]   provides service File_system
0.3 [runtime] child "ram_fs" announces service "File_system"
0.3 [runtime -> ps2] i8042: no controller detected
0.3 [runtime -> boot_fb] using boot framebuffer: 2560x1600x32 @ 0x8000000000 type=1 pitch=10240 -> 2560x1600
0.3 [runtime -> nvme] Error: DBGDI:2498
0.6 [runtime] child "usb" announces service "Usb"
0.6 [runtime -> usb] SLUB: HWalign=64, Order=0-1, MinObjects=0, CPUs=1, Nodes=1
0.6 [runtime -> usb] NR_IRQS: 4352, nr_irqs: 4352, preallocated irqs: 256
0.6 [runtime -> usb] clocksource: dde_counter: mask: 0xffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 3526361616960 ns
0.6 [runtime -> usb] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
--
0.6 [runtime -> usb] hub 7-0:1.0: 5 ports detected
0.6 [runtime -> usb] usb usb8: We don't know the algorithms for LPM for this host, disabling LPM.
0.6 [runtime -> usb] hub 8-0:1.0: USB hub found
0.6 [runtime -> usb] hub 8-0:1.0: 2 ports detected
0.6 [runtime -> usb] sched_clock: Marking stable (51720000, 12377000)->(66243000, -2146000)
0.7 [drivers -> platform] Error: io_mem runtime -> nvme ->  cap=cap<invalid>
0.7 [runtime -> nvme] Error: _ds_cap 96 cap=cap<invalid>
0.7 [runtime -> nvme] Error: Uncaught exception of type 'Genode::Attached_dataspace::Invalid_dataspace'
0.7 [runtime -> nvme] Warning: abort called - thread: ep
0.8 [runtime -> usb] usb 5-1: new high-speed USB device number 2 using xhci_hcd
0.9 [runtime -> usb] usb 7-1: new full-speed USB device number 2 using xhci_hcd
1.0 [runtime -> usb] usb 2-1: new SuperSpeed USB device number 2 using xhci_hcd
1.3 [runtime -> usb] usb 8-2: new SuperSpeed Plus Gen 2x1 USB device number 2 using xhci_hcd
1.4 [runtime -> usb] hub 8-2:1.0: USB hub found

[Nos]

I forgot to mention that the wired network module is working now! According to the instruction from @jws I just changed the wifi to usb_net in the nic_router file. Many thanks for that!

[alex-ab]

Thanks @jjkarcher and @Nos. Unfortunately the output did not reveal what we wanted to see. I prepared another debug image https://depot.genode.org/alex-ab/images/sculpt-pc-2026-02-06-debug.img

The image will be bit verbose for all kind of devices, we (Josef and me) are interested in output regarding nvme alike:

[init → runtime → nvme] Error: DBGDI:2498
[init → drivers → platform] Error: 0x1d23a0 Device_component(): create io_mem : 336 'runtime → nvme → ’ device=01:00.0 [000000005c400000,000000005c404000) bar.number=0
[init → drivers → platform] Error: 0x1d23a0 Device_component(): create io_mem : 338 'runtime → nvme → ’ device=01:00.0
[init → drivers → platform] Error: 0x1d23a0 Device_component(): create io_mem : 341 'runtime → nvme → ’ device=01:00.0
[init → drivers → platform] Error: 0x1d23a0 Device_component() exception : 397 'runtime → nvme → ’ device=01:00.0
[init → drivers → platform] Error: 0x1d23a0 Device_component: release resources : 25 'runtime → nvme → ’ device=01:00.0
[init → drivers → platform] Error: 0x1d23a0 Device_component: release resources : 28 'runtime → nvme → ’ device=01:00.0 io_mem=[000000005c400000,000000005c404000)
[init → drivers → platform] Error: 0x1d23a0 Device_component(): create io_mem : 336 'runtime → nvme → ’ device=01:00.0 [000000005c400000,000000005c404000) bar.number=0
[init → drivers → platform] Error: 0x1d23a0 Device_component(): create io_mem : 338 'runtime → nvme → ’ device=01:00.0
[init → drivers → platform] Error: 0x1d23a0 Device_component(): create io_mem : 341 'runtime → nvme → ’ device=01:00.0
[init → drivers → platform] Error: 0x1d23a0 Device_component() done : 395 'runtime → nvme → ’ device=01:00.0
[init → drivers → platform] Error: 0x1d23a0 Device_component::io_mem() : 127 'runtime → nvme → ’ cap=cap<34753> idx=0 io_mems=1 device=01:00.0
[init → drivers → platform] Error: 0x1d23a0 Device_component::io_mem() : 134 'runtime → nvme → ’ cap=cap<34753> idx=0 io_mems=1 device=01:00.0

[Nos]

Good evening,

I tried your new image. Here comes the (shortened) output:

$ grep -5 -iE "nvme|warn|err" log
0.0 [core]  ROM: [0000000056a4f000,0000000056acf900) monitor
0.0 [core]  ROM: [0000000056ee2000,0000000056f39128) ncurses.lib.so
0.0 [core]  ROM: [00000000552d0000,0000000055364b98) nic_router
0.0 [core]  ROM: [0000000056b60000,0000000056b61e76) nic_router.xsd
0.0 [core]  ROM: [0000000052bae000,0000000052c2f670) nitpicker
0.0 [core]  ROM: [0000000055395000,00000000553d61c0) nvme
0.0 [core]  ROM: [0000000055a53000,0000000055a81ef0) part_block
0.0 [core]  ROM: [0000000054f0a000,0000000055258228) pc_intel_fb
0.0 [core]  ROM: [0000000056fbf000,000000005715d228) pc_nic
0.0 [core]  ROM: [0000000055b72000,0000000055c1f260) pc_platform
0.0 [core]  ROM: [0000000057206000,0000000057378e10) pc_usb_host
--
0.0 [core]  ROM: [000000005588b000,0000000055982558) wpa_supplicant.lib.so
0.0 [core]  ROM: [0000000056a13000,0000000056a2b230) zlib.lib.so
0.0 [core] 335900K kernel memory
0.0 [core] Genode sculpt-25.10.1-12-g5d28f097bc <local changes>
0.0 [core] 31646 MiB RAM and 63256 caps assigned to init
0.0 [core] [init] Warning: runtime: configured RAM exceeds available RAM, proceed with 32671308112
0.0 [runtime] parent provides
0.0 [runtime]   service "ROM"
0.0 [runtime]   service "PD"
0.0 [runtime]   service "RM"
0.0 [runtime]   service "CPU"
--
0.0 [drivers -> acpi] Found MCFG
0.0 [drivers -> acpi] MCFG BASE 0xe0000000 seg 0x0 bus 0x0-0xff
0.0 [drivers -> acpi] Found IVRS
0.0 [drivers -> acpi] XSDT OEM 'INSYDE', table id 'EDK2    ', revision 2, creator '    ' (16777235)
0.0 [drivers -> acpi] SMBIOSv2 table (entry point: 0x16f000 structures: 0x58e75000)
0.1 [drivers -> pci_decode] Warning: Unsupported TPM2 device found
0.3 [runtime] parent provides
0.3 [runtime]   service "VM"
0.3 [runtime]   service "Usb"
0.3 [runtime]   service "File_system"
0.3 [runtime]   service "Rtc"
--
0.3 [runtime]   RAM quota:  16136K
0.3 [runtime]   cap quota:  166
0.3 [runtime]   ELF binary: usb
0.3 [runtime]   priority:   2
0.3 [runtime]   provides service Usb
0.3 [runtime] child "nvme"
0.3 [runtime]   RAM quota:  7944K
0.3 [runtime]   cap quota:  66
0.3 [runtime]   ELF binary: nvme
0.3 [runtime]   priority:   3
0.3 [runtime]   provides service Block
0.3 [runtime] child "runtime_view"
0.3 [runtime]   RAM quota:  53000K
0.3 [runtime]   cap quota:  296
--
0.3 [runtime]   cap quota:  266
0.3 [runtime]   ELF binary: vfs
0.3 [runtime]   priority:   2
0.3 [runtime]   provides service File_system
0.3 [runtime] child "ram_fs" announces service "File_system"
0.3 [drivers -> platform] Error: 0x188130 Device_component() done : 395 'runtime -> ps2 -> ' device=ps2
0.3 [runtime -> ps2] i8042: no controller detected
0.3 [runtime -> boot_fb] using boot framebuffer: 2560x1600x32 @ 0x8000000000 type=1 pitch=10240 -> 2560x1600
0.3 [runtime -> nvme] Error: DBGDI:2498
0.6 [runtime] child "usb" announces service "Usb"
0.6 [runtime -> usb] SLUB: HWalign=64, Order=0-1, MinObjects=0, CPUs=1, Nodes=1
0.6 [runtime -> usb] NR_IRQS: 4352, nr_irqs: 4352, preallocated irqs: 256
0.6 [runtime -> usb] clocksource: dde_counter: mask: 0xffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 3526361616960 ns
0.6 [runtime -> usb] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
0.6 [runtime -> usb] usbcore: registered new interface driver usbfs
0.6 [runtime -> usb] usbcore: registered new interface driver hub
0.6 [runtime -> usb] usbcore: registered new device driver usb
0.6 [runtime -> usb] clocksource: Switched to clocksource dde_counter
0.6 [runtime -> usb] usbcore: registered new interface driver genode
0.6 [drivers -> platform] Error: 0x1a8210 Device_component(): create io_mem : 336 'runtime -> usb -> ' device=c3:00.4 [0000000090700000,0000000090800000) bar.number=0
0.6 [drivers -> platform] Error: 0x1a8210 Device_component(): create io_mem : 338 'runtime -> usb -> ' device=c3:00.4
0.6 [drivers -> platform] Error: 0x1a8210 Device_component(): create io_mem : 341 'runtime -> usb -> ' device=c3:00.4
0.6 [drivers -> platform] Error: 0x1a8210 Device_component() done : 395 'runtime -> usb -> ' device=c3:00.4
0.6 [drivers -> platform] Error: 0x1a8210 Device_component::io_mem() : 127 'runtime -> usb -> ' cap=cap<34656> idx=0 io_mems=1 device=c3:00.4
0.6 [drivers -> platform] Error: 0x1a8210 Device_component::io_mem() : 134 'runtime -> usb -> ' cap=cap<34656> idx=0 io_mems=1 device=c3:00.4
0.6 [runtime -> usb] xhci_hcd c3:00.4: xHCI Host Controller
0.6 [runtime -> usb] xhci_hcd c3:00.4: new USB bus registered, assigned bus number 1
0.6 [runtime -> usb] xhci_hcd c3:00.4: hcc params 0x0110ffc5 hci version 0x120 quirks 0x0000000200000010
0.6 [runtime -> usb] xhci_hcd c3:00.4: xHCI Host Controller
0.6 [runtime -> usb] xhci_hcd c3:00.4: new USB bus registered, assigned bus number 2
--
0.6 [runtime -> usb] hub 1-0:1.0: USB hub found
0.6 [runtime -> usb] hub 1-0:1.0: 1 port detected
0.6 [runtime -> usb] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
0.6 [runtime -> usb] hub 2-0:1.0: USB hub found
0.6 [runtime -> usb] hub 2-0:1.0: 1 port detected
0.6 [drivers -> platform] Error: 0x1a8700 Device_component: 303 'runtime -> usb -> ' device=c3:00.3
0.6 [drivers -> platform] Error: 0x1a8700 Device_component(): create io_mem : 336 'runtime -> usb -> ' device=c3:00.3 [0000000090600000,0000000090700000) bar.number=0
0.6 [drivers -> platform] Error: 0x1a8700 Device_component() exception : 397 'runtime -> usb -> ' device=c3:00.3
0.6 [drivers -> platform] Error: 0x1a8700 Device_component: release resources : 25 'runtime -> usb -> ' device=c3:00.3
0.6 [drivers -> platform] Error: 0x1a8700 Device_component(): create io_mem : 336 'runtime -> usb -> ' device=c3:00.3 [0000000090600000,0000000090700000) bar.number=0
0.6 [drivers -> platform] Error: 0x1a8700 Device_component() exception : 397 'runtime -> usb -> ' device=c3:00.3
0.6 [drivers -> platform] Error: 0x1a8700 Device_component: release resources : 25 'runtime -> usb -> ' device=c3:00.3
0.6 [drivers -> platform] Error: 0x1a8700 Device_component(): create io_mem : 336 'runtime -> usb -> ' device=c3:00.3 [0000000090600000,0000000090700000) bar.number=0
0.6 [drivers -> platform] Error: 0x1a8700 Device_component(): create io_mem : 338 'runtime -> usb -> ' device=c3:00.3
0.6 [drivers -> platform] Error: 0x1a8700 Device_component(): create io_mem : 341 'runtime -> usb -> ' device=c3:00.3
0.6 [drivers -> platform] Error: 0x1a8700 Device_component() done : 395 'runtime -> usb -> ' device=c3:00.3
0.6 [drivers -> platform] Error: 0x1a8700 Device_component::io_mem() : 127 'runtime -> usb -> ' cap=cap<34668> idx=0 io_mems=1 device=c3:00.3
0.6 [drivers -> platform] Error: 0x1a8700 Device_component::io_mem() : 134 'runtime -> usb -> ' cap=cap<34668> idx=0 io_mems=1 device=c3:00.3
0.6 [runtime -> usb] xhci_hcd c3:00.3: xHCI Host Controller
0.6 [runtime -> usb] xhci_hcd c3:00.3: new USB bus registered, assigned bus number 3
0.6 [runtime -> usb] xhci_hcd c3:00.3: hcc params 0x0110ffc5 hci version 0x120 quirks 0x0000000200000010
0.6 [runtime -> usb] xhci_hcd c3:00.3: xHCI Host Controller
0.6 [runtime -> usb] xhci_hcd c3:00.3: new USB bus registered, assigned bus number 4
--
0.6 [runtime -> usb] hub 3-0:1.0: USB hub found
0.6 [runtime -> usb] hub 3-0:1.0: 1 port detected
0.6 [runtime -> usb] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
0.6 [runtime -> usb] hub 4-0:1.0: USB hub found
0.6 [runtime -> usb] hub 4-0:1.0: 1 port detected
0.6 [drivers -> platform] Error: 0x1a8c60 Device_component() exception : 397 'runtime -> usb -> ' device=c1:00.4
0.6 [drivers -> platform] Error: 0x1a8c60 Device_component: release resources : 25 'runtime -> usb -> ' device=c1:00.4
0.6 [drivers -> platform] Error: 0x1a8c60 Device_component(): create io_mem : 336 'runtime -> usb -> ' device=c1:00.4 [0000000090300000,0000000090400000) bar.number=0
0.6 [drivers -> platform] Error: 0x1a8c60 Device_component() exception : 397 'runtime -> usb -> ' device=c1:00.4
0.6 [drivers -> platform] Error: 0x1a8c60 Device_component: release resources : 25 'runtime -> usb -> ' device=c1:00.4
0.6 [drivers -> platform] Error: 0x1a8c60 Device_component(): create io_mem : 336 'runtime -> usb -> ' device=c1:00.4 [0000000090300000,0000000090400000) bar.number=0
0.6 [drivers -> platform] Error: 0x1a8c60 Device_component(): create io_mem : 338 'runtime -> usb -> ' device=c1:00.4
0.6 [drivers -> platform] Error: 0x1a8c60 Device_component(): create io_mem : 341 'runtime -> usb -> ' device=c1:00.4
0.6 [drivers -> platform] Error: 0x1a8c60 Device_component() exception : 397 'runtime -> usb -> ' device=c1:00.4
0.6 [drivers -> platform] Error: 0x1a8c60 Device_component: release resources : 25 'runtime -> usb -> ' device=c1:00.4
0.6 [drivers -> platform] Error: 0x1a8c60 Device_component: release resources : 28 'runtime -> usb -> ' device=c1:00.4 io_mem=[0000000090300000,0000000090400000)
0.6 [drivers -> platform] Error: 0x1a8c60 Device_component(): create io_mem : 336 'runtime -> usb -> ' device=c1:00.4 [0000000090300000,0000000090400000) bar.number=0
0.6 [drivers -> platform] Error: 0x1a8c60 Device_component(): create io_mem : 338 'runtime -> usb -> ' device=c1:00.4
0.6 [drivers -> platform] Error: 0x1a8c60 Device_component(): create io_mem : 341 'runtime -> usb -> ' device=c1:00.4
0.6 [drivers -> platform] Error: 0x1a8c60 Device_component() done : 395 'runtime -> usb -> ' device=c1:00.4
0.6 [drivers -> platform] Error: 0x1a8c60 Device_component::io_mem() : 127 'runtime -> usb -> ' cap=cap<34682> idx=0 io_mems=1 device=c1:00.4
0.6 [drivers -> platform] Error: 0x1a8c60 Device_component::io_mem() : 134 'runtime -> usb -> ' cap=cap<34682> idx=0 io_mems=1 device=c1:00.4
0.6 [runtime -> usb] xhci_hcd c1:00.4: xHCI Host Controller
0.6 [runtime -> usb] xhci_hcd c1:00.4: new USB bus registered, assigned bus number 5
0.6 [runtime -> usb] xhci_hcd c1:00.4: hcc params 0x0110ffc5 hci version 0x120 quirks 0x0000000200000010
0.6 [runtime -> usb] xhci_hcd c1:00.4: xHCI Host Controller
0.6 [runtime -> usb] xhci_hcd c1:00.4: new USB bus registered, assigned bus number 6
--
0.6 [runtime -> usb] hub 5-0:1.0: USB hub found
0.6 [runtime -> usb] hub 5-0:1.0: 1 port detected
0.6 [runtime -> usb] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
0.6 [runtime -> usb] hub 6-0:1.0: USB hub found
0.6 [runtime -> usb] hub 6-0:1.0: 1 port detected
0.7 [drivers -> platform] Error: 0x1a9150 Device_component() exception : 397 'runtime -> usb -> ' device=c1:00.3
0.7 [drivers -> platform] Error: 0x1a9150 Device_component: release resources : 25 'runtime -> usb -> ' device=c1:00.3
0.7 [drivers -> platform] Error: 0x1a9150 Device_component(): create io_mem : 336 'runtime -> usb -> ' device=c1:00.3 [0000000090200000,0000000090300000) bar.number=0
0.7 [drivers -> platform] Error: 0x1a9150 Device_component() exception : 397 'runtime -> usb -> ' device=c1:00.3
0.7 [drivers -> platform] Error: 0x1a9150 Device_component: release resources : 25 'runtime -> usb -> ' device=c1:00.3
0.7 [drivers -> platform] Error: 0x1a9150 Device_component(): create io_mem : 336 'runtime -> usb -> ' device=c1:00.3 [0000000090200000,0000000090300000) bar.number=0
0.7 [drivers -> platform] Error: 0x1a9150 Device_component(): create io_mem : 338 'runtime -> usb -> ' device=c1:00.3
0.7 [drivers -> platform] Error: 0x1a9150 Device_component(): create io_mem : 341 'runtime -> usb -> ' device=c1:00.3
0.7 [drivers -> platform] Error: 0x1a9150 Device_component() exception : 397 'runtime -> usb -> ' device=c1:00.3
0.7 [drivers -> platform] Error: 0x1a9150 Device_component: release resources : 25 'runtime -> usb -> ' device=c1:00.3
0.7 [drivers -> platform] Error: 0x1a9150 Device_component: release resources : 28 'runtime -> usb -> ' device=c1:00.3 io_mem=[0000000090200000,0000000090300000)
0.7 [drivers -> platform] Error: 0x1a9150 Device_component(): create io_mem : 336 'runtime -> usb -> ' device=c1:00.3 [0000000090200000,0000000090300000) bar.number=0
0.7 [drivers -> platform] Error: 0x1a9150 Device_component(): create io_mem : 338 'runtime -> usb -> ' device=c1:00.3
0.7 [drivers -> platform] Error: 0x1a9150 Device_component(): create io_mem : 341 'runtime -> usb -> ' device=c1:00.3
0.7 [drivers -> platform] Error: 0x1a9150 Device_component() done : 395 'runtime -> usb -> ' device=c1:00.3
0.7 [drivers -> platform] Error: 0x1a9150 Device_component::io_mem() : 127 'runtime -> usb -> ' cap=cap<34694> idx=0 io_mems=1 device=c1:00.3
0.7 [drivers -> platform] Error: 0x1a9150 Device_component::io_mem() : 134 'runtime -> usb -> ' cap=cap<34694> idx=0 io_mems=1 device=c1:00.3
0.7 [runtime -> usb] xhci_hcd c1:00.3: xHCI Host Controller
0.7 [runtime -> usb] xhci_hcd c1:00.3: new USB bus registered, assigned bus number 7
0.7 [runtime -> usb] xhci_hcd c1:00.3: hcc params 0x0128ffc5 hci version 0x120 quirks 0x0000000200000010
0.7 [runtime -> usb] xhci_hcd c1:00.3: xHCI Host Controller
0.7 [runtime -> usb] xhci_hcd c1:00.3: new USB bus registered, assigned bus number 8
--
0.7 [runtime -> usb] hub 7-0:1.0: 5 ports detected
0.7 [runtime -> usb] usb usb8: We don't know the algorithms for LPM for this host, disabling LPM.
0.7 [runtime -> usb] hub 8-0:1.0: USB hub found
0.7 [runtime -> usb] hub 8-0:1.0: 2 ports detected
0.7 [runtime -> usb] sched_clock: Marking stable (99206000, 10986000)->(111922000, -1730000)
0.7 [drivers -> platform] Error: 0x198130 Device_component() done : 395 'runtime -> nvme -> ' device=00:03.2
0.7 [drivers -> platform] Error: 0x198130 Device_component::io_mem() : 134 'runtime -> nvme -> ' cap=cap<invalid> idx=0 io_mems=0 device=00:03.2
0.7 [runtime -> nvme] Error: _ds_cap 96 cap=cap<invalid>
0.7 [runtime -> nvme] Error: Uncaught exception of type 'Genode::Attached_dataspace::Invalid_dataspace'
0.7 [runtime -> nvme] Warning: abort called - thread: ep
0.9 [runtime -> usb] usb 1-1: new full-speed USB device number 2 using xhci_hcd
0.9 [runtime -> usb] usb 5-1: new high-speed USB device number 2 using xhci_hcd
1.0 [runtime -> usb] usb 7-1: new full-speed USB device number 2 using xhci_hcd
1.2 [runtime] child "usb_hid"
1.2 [runtime]   RAM quota:  11016K
--
1.9 [runtime] child "usb-8-3" announces service "Block"
1.9 [runtime -> usb-8-3.part] GPT Partition 1: LBA 40 (101 blocks) type: '21686148-6449-6e6f-744e-656564454649' name: 'BIOSBOOT'
1.9 [runtime -> usb-8-3.part] GPT Partition 2: LBA 141 (4515 blocks) type: 'c12a7328-f81f-11d2-ba4b-00a0c93ec93b' name: 'GRUB2'
1.9 [runtime -> usb-8-3.part] GPT Partition 3: LBA 4952 (67888 blocks) type: '0fc63daf-8483-4772-8e79-3d69d8477de4' name: 'GENODE'
1.9 [runtime] child "usb-8-3.part" announces service "Block"
2.0 [core] [init -> nitpicker] Warning: Gui (leitzentrale -> manager -> fader -> ) not enough RAM to preserve buffer content during resize
2.0 [runtime -> usb] hub 7-3:1.0: USB hub found
2.0 [runtime -> usb] hub 7-3:1.0: 3 ports detected
2.0 [runtime -> usb] usb 8-2.3: new SuperSpeed USB device number 4 using xhci_hcd
2.1 [runtime -> usb] usb 8-2.2: reset SuperSpeed USB device number 3 using xhci_hcd
2.3 [runtime -> usb] usb 7-4: new high-speed USB device number 5 using xhci_hcd
--
3.7 [runtime -> usb_hid] hid-generic 0003:32AC:0018.000A: device has no listeners, quitting
12.5 [runtime -> usb] usb 7-2.1: new low-speed USB device number 10 using xhci_hcd
12.7 [runtime -> usb_hid] input: Logitech USB Optical Mouse as /devices/usb-7-10/0-0:1.0/0003:046D:C05B.000B/input/input10
12.8 [runtime -> usb_hid] Connected device: input10 (Logitech USB Optical Mouse at usb-usbbus-0/input0) MOUSE
12.8 [runtime -> usb_hid] hid-generic 0003:046D:C05B.000B: input: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-usbbus-0/input0
14.8 [runtime -> runtime_view] Warning: attempt to handle the same signal context twice (nested)
23.4 [runtime] child "usb-8-3"
23.4 [runtime]   RAM quota:  5896K
23.4 [runtime]   cap quota:  66
23.4 [runtime]   ELF binary: usb_block
23.4 [runtime]   priority:   3
--
24.0 [runtime -> usb-8-3.part] GPT Partition 3: LBA 4952 (60120198 blocks) type: '0fc63daf-8483-4772-8e79-3d69d8477de4' name: 'GENODE'
24.0 [runtime] child "usb-8-3.part" announces service "Block"
24.0 [runtime -> usb-8-3.3.resize2fs] resize2fs 1.46.5 (30-Dec-2021)
24.0 [runtime -> usb-8-3.3.resize2fs] Resizing the filesystem on /dev/block to 7515024 (4k) blocks.
24.3 [runtime -> usb-8-3.3.resize2fs] Begin pass 1 (max = 229)
24.3 [runtime -> usb-8-3] Warning: SCSI command failure, expected tag=29, got tag=29 status=1
24.3 [runtime -> usb-8-3] Error: Request_sense_response asc: 0x20 asq: 0x0
63.6 [runtime -> usb-8-3.3.resize2fs] Extending the inode table     XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
64.3 [runtime -> usb-8-3.3.resize2fs] The filesystem on /dev/block is now 7515024 (4k) blocks long.
64.3 [runtime -> usb-8-3.3.resize2fs] 
64.3 [runtime] child "usb-8-3.3.resize2fs" exited with exit value 0
64.3 [runtime] child "usb-8-3.part"
--
80.1 [runtime] child "usb-8-3" announces service "Block"
80.2 [runtime -> usb-8-3.part] GPT Partition 1: LBA 40 (101 blocks) type: '21686148-6449-6e6f-744e-656564454649' name: 'BIOSBOOT'
80.2 [runtime -> usb-8-3.part] GPT Partition 2: LBA 141 (4515 blocks) type: 'c12a7328-f81f-11d2-ba4b-00a0c93ec93b' name: 'GRUB2'
80.2 [runtime -> usb-8-3.part] GPT Partition 3: LBA 4952 (60120198 blocks) type: '0fc63daf-8483-4772-8e79-3d69d8477de4' name: 'GENODE*'
80.2 [runtime] child "usb-8-3.part" announces service "Block"
80.2 [runtime -> usb-8-3] Warning: SCSI command failure, expected tag=15, got tag=15 status=1
80.2 [runtime -> usb-8-3] Error: Request_sense_response asc: 0x20 asq: 0x0
80.2 [runtime] child "usb-8-3.3.fs" announces service "File_system"
80.2 [runtime] child "depot" announces service "File_system"
80.2 [runtime -> prepare -> bash] Error: no plugin found for fcntl(3)
80.2 [runtime -> prepare -> bash] Error: no plugin found for fcntl(4)
80.2 [runtime -> prepare -> bash] Error: no plugin found for fcntl(5)
80.2 [runtime -> prepare -> bash] Error: no plugin found for fcntl(6)
80.2 [runtime -> prepare -> bash] Error: no plugin found for fcntl(7)
80.2 [runtime -> prepare -> bash] Error: no plugin found for fcntl(8)
80.2 [runtime -> prepare -> bash] Error: no plugin found for fcntl(9)
80.2 [runtime -> prepare -> bash] Error: no plugin found for fcntl(10)
80.2 [runtime -> prepare -> bash] Error: no plugin found for fcntl(11)
80.2 [runtime -> prepare -> bash] Error: no plugin found for fcntl(12)
80.2 [runtime -> prepare -> bash] Error: no plugin found for fcntl(13)
80.2 [runtime -> prepare -> bash] Error: no plugin found for fcntl(14)
80.2 [runtime -> prepare -> bash] Error: no plugin found for fcntl(15)
80.2 [runtime -> prepare -> bash] Error: no plugin found for fcntl(16)
80.2 [runtime -> prepare -> bash] Error: no plugin found for fcntl(17)
80.2 [runtime -> prepare -> bash] Error: no plugin found for fcntl(18)
80.2 [runtime -> prepare -> bash] Error: no plugin found for fcntl(19)
80.9 [runtime] child "prepare" exited with exit value 0
80.9 [runtime] child "launcher_query"
80.9 [runtime]   RAM quota:  1800K
80.9 [runtime]   cap quota:  166
80.9 [runtime]   ELF binary: fs_query
--
104.5 [runtime] child "inspect"
104.5 [runtime]   RAM quota:  77576K
104.5 [runtime]   cap quota:  966
104.5 [runtime]   ELF binary: init
104.5 [runtime]   priority:   2
106.5 [leitzentrale -> nitpicker] Warning: Gui (wm -> runtime -> leitzentrale -> inspect) not enough RAM to preserve buffer content during resize

I hope its helpful. While booting the image for the first time I extended the genode partion at the usb thumb-drive and made it the default. Of course I clicked on “use” too.

There is a nvme component showing up in the Leitzentrale but it seems to be empty.
Even drivers/devices does not contain nvme entries:cat drivers/devices | grep -i nvme.

[jjkarcher]

I also captured a log using this image, and the relevant (“nvme”) lines are exactly the same as @Nos’s, including the numbers.

Thanks again!